[SLO.M3]

So my wheels came in a week after my G01 was totaled and I never got the chance to install them…

Luckily enough I was able to find a local buyer on FB marketplace who loved the design and wanted them for his Pre LCI G01!

Thought I’d share how it turned out with yall. Obviously I’m a huge fan and love how they turned out, but interested to know what you guys think. He’s planning to go coilovers to help tuck it in the rear some more

[deviation01]

Originally Posted by 5LEEPR_G01

So my wheels came in a week after my G01 was totaled and I never got the chance to install them…

Luckily enough I was able to find a local buyer on FB marketplace who loved the design and wanted them for his Pre LCI G01!

Thought I’d share how it turned out with yall. Obviously I’m a huge fan and love how they turned out, but interested to know what you guys think. He’s planning to go coilovers to help tuck it in the rear some more

Sorry to hear about the car. Glad you are ok.

I do like the look and the flow. Very unique but looks classy.

[Camman]

Hey guys, I’ve been doing some research into wheels and I’m curious if 765m wheels can be made and if anyone has gotten any? I like 892m wheels but I love the simplicity of the 765m wheels so I go back and forth on which ones I want to get. TIA

[BFiftyNate]

Originally Posted by Khoury95

Looking into getting a set myself but want to stick with the 21’s. I know the factory width / offset but notice a lot of people running spacers with 892M’s. Any idea what a better offset would be to get a more flush fitment?

Hey - I’m also interested on going 21” on the 892m. New m40i owner here, so just starting out looking into all of this. Based on what I’ve found, offset (et) is not impacted by diameter when it comes to how much the wheel pokes out. The common spec here most seem to be going is 20 x 10 et25. Which means similarly 21” x 10 et25 should be good, if you wanted to do squared.

Another way to think about this is most people running spacers seem to be running either 12 or 15mm on the 892m. The OEM spec for the rear is 21” x 10 et39. Making this an et25 would be the same as adding a 14mm spacer on OEM rims. I don’t think anyone makes a 14mm spacer. I’ve also seen some comments that 15mm poke a hair on the rear, so a 14mm equivalent at et25 makes sense to me.

For the front, the OEM spec is 21” x 9.5 et31. If you wanted to get the outside of the rim at roughly the same location as the 20x10et25, you’d be looking at an et 19 (only a 0.4mm difference, you wouldn’t be able to tell). This is the same as someone adding a 12mm spacer to the 892m OEM spec.

TLDR - I think a flush staggered fitment is:
Front: 21” x 9.5 et19
Rear: 21” x 10 et25

Please fact check me. Anyone running this?

I want absolutely zero chance of rubbing, so I might up the et a bit to be safer. Still undecided on squared vs staggered, but want to go with the 21". I also plan on running the stock 19's as a winter setup.

[swaggyjay13]

Center caps were delivered this week. As others mentioned, this is typical for them to be sent separately and I would expect the wheels by EOM or mid-March latest.

Question - I noticed one of the wheel cap packages came with an “M” for the wheel. Out of the 4 cap packages, mine only came with 1 “M.” Is this normal??

**Note cap still has protective film on it

[peeezy]

Originally Posted by swaggyjay13

Center caps were delivered this week. As others mentioned, this is typical for them to be sent separately and I would expect the wheels by EOM or mid-March latest.

Question - I noticed one of the wheel cap packages came with an “M” for the wheel. Out of the 4 cap packages, mine only came with 1 “M.” Is this normal??

**Note cap still has protective film on it

contact the supplier and ask where the other 3 “M” badges are

[swaggyjay13]

Originally Posted by peeezy

contact the supplier and ask where the other 3 “M” badges are

Update - Jason said the rest are on the wheels itself. This one was a “bonus gift” haha.

[BeastLG]

Hi guys, been following this thread for a long time and am thinking about pulling the trigger on some 892m's in a 20x10 square setup. I have a ping out to XY Wheels, but I also went out to another well regarded manufacturer on a few forums - WF Wheels (WForged Wheels). I am still waiting on a response from XY, but WF got back to me almost instantly and recommended I go with ET23. I see a lot of people posting about going with ET25. Any thoughts?

[deviation01]

Originally Posted by BeastLG

Hi guys, been following this thread for a long time and am thinking about pulling the trigger on some 892m's in a 20x10 square setup. I have a ping out to XY Wheels, but I also went out to another well regarded manufacturer on a few forums - WF Wheels (WForged Wheels). I am still waiting on a response from XY, but WF got back to me almost instantly and recommended I go with ET23. I see a lot of people posting about going with ET25. Any thoughts?

Page 22 on the thread also has some detail on ET23.

Its really up to you. How wide of a wheel may have an impact too?

The ET23 will sit 2mm further outward. So you will be 2mm closer to the fender lip. I think under full compression with 275 tire you run the risk of rubbing but could be similar with et25 just you have more wiggle room.

[BeastLG]

Pulled the trigger on a set of 892M's from XY as well! Thanks to this thread, I am feeling pretty confident on my choices!

[BeastLG]

Originally Posted by swaggyjay13

Finally ordered my wheels - 892M style OEM finish ( 20x10xET25).

Wondering if anyone else has ordered similar wheels and can recommend tire size?

Would love a wider/fuller if tire size makes a difference.

Thanks in advance guys - let the wait begin!!

This is a bit interesting, the wheels have a different weight and max load vs. the blue prints on your wheel swaggyjay13.

[peeezy]

Originally Posted by BeastLG

This is a bit interesting, the wheels have a different weight and max load vs. the blue prints on your wheel swaggyjay13.

i noticed that also. im assuming in china they are just guessing the wheel weight based on specs n design untill it is actually finished.
my wheel shows a 11.7kg weight and a max load of 850kg on there 3d drawing with the company i am using(x-town wheels)

[Steelers6891]

Originally Posted by swaggyjay13

Finally ordered my wheels - 892M style OEM finish ( 20x10xET25).

Wondering if anyone else has ordered similar wheels and can recommend tire size?

Would love a wider/fuller if tire size makes a difference.

Thanks in advance guys - let the wait begin!

Have you decided on a tire size yet? I?m getting ready to order tires and finally mount these but I?m unsure on tire size still. Im thinking 275/40

[BeastLG]

Originally Posted by swaggyjay13

Finally ordered my wheels - 892M style OEM finish ( 20x10xET25).

Wondering if anyone else has ordered similar wheels and can recommend tire size?

Would love a wider/fuller if tire size makes a difference.

Thanks in advance guys - let the wait begin!!

Curious if you got your wheels yet!

[Circa Surviven]

Originally Posted by Jb427

They’re great so far, solid even at speed. About to swap to ceramic brembo pads to hopefully take care of the brake dust the oem pads throw off.

Those M parallel's are sick!

[ajt27]

Can anyone provide a long term review of the quality of these wheels?

[deviation01]

Originally Posted by ajt27

Can anyone provide a long term review of the quality of these wheels?

Mine have been sitting in the box for a year so I cant. I will install them next month.

Budget was not there with wedding and such

[MyOtherCarWRX]

Originally Posted by deviation01

Mine have been sitting in the box for a year so I cant. I will install them next month.

Budget was not there with wedding and such

Just sell them to me then you reorder 😁

[deviation01]

Originally Posted by MyOtherCarWRX

Just sell them to me then you reorder 😁

haha noo i like mine I am yet to see someone going with those wheels on their X3.

[MyOtherCarWRX]

Originally Posted by deviation01

haha noo i like mine I am yet to see someone going with those wheels on their X3.

I'm also looking to get a set of BBS FI-R but staggered probably. Cant decide on exact specs yet though. And a 2 months wait gonne kill me

[deviation01]

Originally Posted by MyOtherCarWRX

I'm also looking to get a set of BBS FI-R but staggered probably. Cant decide on exact specs yet though. And a 2 months wait gonne kill me

They look great. Its a bit extra cost to make the hallow design (holes). They have to use a special machine to cut the holes in the spokes etc. but they look great to me. I will have them mounted on my car next month and post pictures.

[peeezy]

my wheels are arriving mid april to canada, but i am buying summer tires now since alot of places are still offering 15% discount for the next week or so before prices increase when warmer weather arrives. michilen ps4 285/40/20