Can anyone help me find the diagram with measurements that show exactly where to place the M-Logos on the front fenders (driver and passenger side)?
For those in Canda or Europe, could you send pictures of the M-Logos with measuring tape from the bottom and side fender (driver and passenger side)?
I would greatly appreciate the help.
6KVIEWS
48REPLIES
35APPRECIATES
13ACTIVE PEOPLE
04-08-2026LAST POST
01-07-2025
01-07-2025
Ravenous666
Colonel
2,186
REP
2.3K
POSTS
I can make a picture and measure from the edges as soon as my M50 arrives. Should be within the next 10 days.
ModernAngel
,
olmaxusa
,
ScoutsoutX00X
01-07-2025
Ravenous666 wroteThank you very much!I can make a picture and measure from the edges as soon as my M50 arrives. Should be within the next 10 days.
01-08-2025
MidnightLight
First Lieutenant
421
REP
394
POSTS
Out of curiosity... what do you intend to do with this information?
01-08-2025
01-08-2025
l33v0nix wroteYeah, no fender badges in US.likely to change blackout badge or i think US does not put the fender badge
01-09-2025
JoeyO
Major
594
REP
1.2K
POSTS
Just install it upside down. That will get people’s attention. :-)
01-09-2025
ColVSC
Registered
4
REP
3
POSTS
Here is where I plan on placing mine after the Xpel PPF is installed.
olmaxusa
01-10-2025
01-12-2025
l33v0nix wroteYes, unfortunately the US model does not attach the fender badges…likely to change blackout badge or i think US does not put the fender badge
02-03-2025
Ravenous666 wroteI can make a picture and measure from the edges as soon as my M50 arrives. Should be within the next 10 days.
Did you recieve your M50?
If so, please make a picture of the fender M badges and measure them from the edges. I would greatly appreciate it.
02-03-2025
Ravenous666
Colonel
2,186
REP
2.3K
POSTS
Will do it tomorrow. Thank you for the patience.
olmaxusa
,
ScoutsoutX00X
02-04-2025
Ravenous666
Colonel
2,186
REP
2.3K
POSTS
So I'm back from work and made the measurement.
The aft edge of the badge is 100mm from the gap to the door
The lower edge of the badge is 550mm from the lower gap of the fender.
The aft edge of the badge is 100mm from the gap to the door
The lower edge of the badge is 550mm from the lower gap of the fender.
olmaxusa
,
ScoutsoutX00X
,
LemurWrangler
+3
02-04-2025
Ravenous666 wroteThank you for your help!So I'm back from work and made the measurement.
The aft edge of the badge is 100mm from the gap to the door
The lower edge of the badge is 550mm from the lower gap of the fender.
02-06-2025
Anyone have the part number for that badge, ideally in black? I got the US model and that fender badge looks nice
javmarmar
02-06-2025
02-06-2025
TanziniteG45 wroteAnyone have the part number for that badge, ideally in black? I got the US model and that fender badge looks nice
02-06-2025
02-06-2025
Ravenous666
Colonel
2,186
REP
2.3K
POSTS
TanziniteG45 wroteNo, it's not. The one on the grill is smaller.Oh, it's the same as the one on the grill. Thanks
See signature for collection of partnumbers.
02-06-2025
I feel like a boomer but I don't see your signature. But I have that thread pulled up so I know the post you're talking about. You've made my life so much easier with your posts!
Correction, you saved me again. I was about to try to apply the fender badge on my grill!
Correction, you saved me again. I was about to try to apply the fender badge on my grill!
Ravenous666
,
ScoutsoutX00X
02-06-2025
Ravenous666
Colonel
2,186
REP
2.3K
POSTS
Just to clarify.
The ones on the fenders are 55mm
The one on the grill is 45mm
M Logo small on Fender black 51145A4B373
M-Logo on M50 grill black 45mmx15mm 51145A4B372
The ones on the fenders are 55mm
The one on the grill is 45mm
M Logo small on Fender black 51145A4B373
M-Logo on M50 grill black 45mmx15mm 51145A4B372
TanziniteG45
,
ScoutsoutX00X
,
Eris496
02-09-2025
