05-06-2021, 10:49 AM | #1 |
Lieutenant Colonel
828
Rep 1,933
Posts |
Need advice- engine bay wash job
Watched a couple videos, couple questions...and give me your tips on this job:
-remove plastic underbelly pan? -disconnect battery? -leave engine cover in place? -cover alternator and other_____components? Thanks/Bill |
05-06-2021, 11:13 AM | #2 |
Colonel
1233
Rep 2,928
Posts |
My answer is no to all four questions. I have washed my engine bays on cars many times and have never has a single issue. I do not shoot a high pressure hose directly at the alternator, the engine computer or major electrical connections or other control units, but it will not hurt them to get wet. The main thing you do not want is to shoot water into the air intake. So depending on what you remove, and how the intake is designed on your engine, a plastic bag and rubber band may be needed.
|
Appreciate
1
Wgosma827.50 |
05-06-2021, 12:45 PM | #3 | |
Captain
283
Rep 888
Posts
Drives: 08 135i M Sport 6MT, 15 X3 35i
Join Date: Feb 2013
Location: Edmonton
|
Quote:
I just spray it down in a wash bay from a few steps back to reduce the pressure. Soap then rinse. Your engine bay gets wet every time you drive on the highway in the rain. The sensitive components like computers are in a dust/waterproof compartment typically. Dust is just as bad as water for computers. Just don't go crazy and never wash a hot engine, I drive 2 minutes down the street to the wash bay, engine is completely cold (ambient temp) before I leave.
__________________
2015 Cosmic Blue Metallic Wrapped X3 35i ///M Sport Full 3M Vinyl Wrap | Flat Black Grilles |
|
Appreciate
1
Wgosma827.50 |
05-06-2021, 04:01 PM | #4 |
Brigadier General
3421
Rep 4,090
Posts |
My tips would be -
Wash in the driveway, and just let the hose dribble on it. Remove dirt with a brush - like a wheel cleaner, something thin on a stick or use a variety of shapes. Tire dressing can make things look decent. Simple green is a good grease cutter. Use chemicals sparingly and try to avoid the belts and pulleys. Generally you should be fine but there's always a chance. On my last car I had to replace the alternator the day after I washed the engine, the bearings were suddenly squealing. Coincidence? Definitely never when it's hot. |
Appreciate
1
Wgosma827.50 |
05-06-2021, 11:43 PM | #5 |
Private
21
Rep 89
Posts |
You start removing things and other components have the potential to get damaged. Engine bay are generally made waterproof.
Don't need pressure washer but if you use it, pull it back a few inches so it won't dislodge anything in there. I use a degreaser spray (super clean) to spray mainly what is on top but in other areas as well only if I can reach it with my brush. Whatever's within reach is fair game. I use a wheel cleaning brush to get in the small areas, bigger brush for engine cover and intake cover, small detail brush for smaller areas. Then a gentle rinse off. It is worth it to dress your engine bay. It protects it and repels dirt so it stays cleaner longer and no discoloration! That's it. |
Appreciate
0
|
05-11-2021, 02:09 PM | #6 |
New Member
0
Rep 6
Posts
Drives: 2016 BMW X3 MSport trim
Join Date: May 2021
Location: Halifax, Nova Scotia, Canada
|
I usually just use a degreasing spray, brush, then use a damp blue automotive wipe. Then go over it again with a plastic protectant/polish.
|
Appreciate
0
|
05-12-2021, 05:36 PM | #7 |
Lieutenant Colonel
828
Rep 1,933
Posts |
I gave it a go today…Dry brushed off loose dust then covered motor w/plastic and washed underside of hood, remove plastic to wash compartment. Used Simple Green to cut the dirt. Looks a lot better!
|
Appreciate
1
tracer bullet3420.50 |
05-13-2021, 02:43 PM | #9 |
Lieutenant Colonel
828
Rep 1,933
Posts |
|
Appreciate
0
|
05-13-2021, 06:32 PM | #10 |
Major
489
Rep 1,469
Posts |
Here is what works:
1) make sure engine is cool. 2) wrap alternator in a plastic bag 3) rinse with power washer or hose 4) apply APC 5) agitate with a wheel or lug brush 6) rinse & apply diluted meguiars hyper dressing 7) let it dry and you'll be amazed.
__________________
2014 EBII 435ix - Stage 2+ Dragy: 0-60 3.61; 60-130 10.18
2020 MG M340ix - Dragy: 0-60 3.48 2018 LBB X4M40i - Stock Dragy: 0-60 4.85 |
Appreciate
0
|
05-15-2021, 08:36 AM | #11 | |
Brigadier General
3421
Rep 4,090
Posts |
Quote:
I tend to agree that things can get wet and are designed to take on rain through the grille and splashes from underneath. However in reality very little gets through either, with the radiator in the front and the paneling underneath. Check the engine after driving in a rainstorm and see how dry it actually is. It should be able to handle it, but it isn't a routine thing. I've cleaned my 135i engine bay only a handful of times total in its life and found recently when I changed plugs and coils that almost across the board they had some rust and corrosion on them. Wasn't enough to actually harm them, but it was proof to me that water can still get into areas you don't expect. It's an N55 same as my X3. Covering things may not be required but I have to say it's definitely good practice. |
|
Appreciate
0
|
06-06-2021, 03:46 PM | #13 |
Lieutenant Colonel
828
Rep 1,933
Posts |
This was first time I've ever done an engine bay cleaning job, it's simple and pretty quick to do- as long as you don't use a fire hose the car is fine.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|