[marcati]

Originally Posted by GoCubs

Does anyone know if there is a way to disable the three dings when you start the engine if the driver's seatbelt is undone? I find them really annoying.

In BimmerCode I disabled the one driver seatbelt option thinking that would do it and unfortunately it did not. However it did disable the warnings if I remove the driver seatbelt while driving.

I disabled all the safety stuff in that module and have no sounds. Just can't remember which was the magic one ;-)

[SoItShallBeWritten]

Forgive me if this has been answered but thread search is very poor...

I have a propensity to open the liftgate accidentally when the remote is in my pocket or I'm laying on the couch at home, etc. Is there a way to disable the liftgate button on the remote....or even increase the delay??? I recall reading that others had this issue as well a while back.

I have Bimmercode and successfully coded some items on the simple guided setup a few months ago. But have not used advanced before. Thanks!

[hobz]

Originally Posted by SoItShallBeWritten

Forgive me if this has been answered but thread search is very poor...

I have a propensity to open the liftgate accidentally when the remote is in my pocket or I'm laying on the couch at home, etc. Is there a way to disable the liftgate button on the remote....or even increase the delay??? I recall reading that others had this issue as well a while back.

I have Bimmercode and successfully coded some items on the simple guided setup a few months ago. But have not used advanced before. Thanks!

With Bimmercode... make 2 changes.
This should make it long press for open and close

Tailgate function remote control
The tailgate function that is triggered when the button on the remote is pressed.

Values:

Open
Open and close

Set to [open and close]


Close tailgate with the remote control without long press
Enable/disable closing the tailgate without a long press of the button on the remote control.


Values:

Active
Not active

Set to [Not active]

[Rhidium]

Originally Posted by SoItShallBeWritten

Forgive me if this has been answered but thread search is very poor...

I have a propensity to open the liftgate accidentally when the remote is in my pocket or I'm laying on the couch at home, etc. Is there a way to disable the liftgate button on the remote....or even increase the delay??? I recall reading that others had this issue as well a while back.

I have Bimmercode and successfully coded some items on the simple guided setup a few months ago. But have not used advanced before. Thanks!

I heard you can disable it but it was through a dealer. I also heard the dealer can disable the sensor until it is unlocked.

I haven't had any issue with fob or trunk sensor inadvertently open my trunk

[Rhidium]

Originally Posted by BrooklynX3

Coded the Alpina Dashboard into the instrument cluster. This thing is super cool! So amazing to look at. It's truly captivating! Also it was super easy to do!

[img]

View post on imgur.com

[/img]

[img]

View post on imgur.com

[/img]

[img]

View post on imgur.com

[/img]

Saw this post about alpine setup and was wonder where are the lines/numbers/etc?

[chicagofan00]

Originally Posted by Rhidium

Saw this post about alpine setup and was wonder where are the lines/numbers/etc?

The car hasn't been started up in those photos.

[fricfracfrank]

Originally Posted by BrooklynX3

Coded the Alpina Dashboard into the instrument cluster. This thing is super cool! So amazing to look at. It's truly captivating! Also it was super easy to do!

I wish this was an option for those without the full digital display

[lo_cheng]

One question. Is there a way to code parking brake to be automatically engage when I put the car in "P" , without using the Auto_hold?

It is so stupid that Auto parking brake is linked with Auto-Hold.
Auto-Hold is just so bad when I sit in traffic.

[Almaretto]

Originally Posted by BigJake

I changed to the Alpina dash but I don't think I noticed any changes.

Changes are immediate. If you do not have 6WB, then you coding will not work.

[Eulenspiegel]

Originally Posted by lo_cheng

One question. Is there a way to code parking brake to be automatically engage when I put the car in "P" , without using the Auto_hold?

It is so stupid that Auto parking brake is linked with Auto-Hold.
Auto-Hold is just so bad when I sit in traffic.

On the first point, good question! What does Auto Hold have to do with engaging the parking brake?

But, what do you have against Auto Hold? Does it kick in too soon in slow, creeping traffic or something?

[Eulenspiegel]

In addition to the coding I reported earlier in this thread (April 20), subject to great risk of hubris, I decided to try a little do-it-yourself Expert coding. More specifically, I wanted to add or substitute German into the very limited list of available languages for US cars in My Vehicle, iDrive, Languages. It didn’t take me long in Headunit, Expert, 3007, to add list German to the iDrive menu, but chosing deutsch wouldn’t save and didn’t do anything anyway. So, searching around, I found Instrument Cluster module, Expert, 3007 PIA_KI_SPRACHE and activtate deutsch.

I’m sure what I did is incomplete in one or more ways, but it does give me German menus in iDrive and German navigation instructions. It even understands my German voice commands (although I will have to learn and remember the specific German names of the various iDrive commands. What it doesn’t do (yet?) is give me a German owner’s manual or a choice of voice input in English, in case my German falls short.

I would be grateful for any suggestions on further steps to improve what I’ve done so far. Of course, even a partial cheat sheet for BimmeCode Expert mode would be of great value.

[chris88]

Hello

work this on the g01?
open and close the car by walk away. like this https://t1p.de/u4e5


HU_NBT_EVO
3000 HMI - CKT_DOOR_LOCK_UNLOCK - aktiv

BDC_BODY2
3030 KeyManager - CKT_ENABLE - aktiv
3030 KeyManager - CKT_FUNCTIONS - light_unlock_lock

[lo_cheng]

I been reading this since I got my M40i 4 weeks ago. Finally got my coding done on the weekend. Here is what I done:

1). Change start up to M startup animation
2). Default Drive mode = Sport Individuel
3). Enable vehicle in motion, Video via USB, and Additional Video codec
4). ADS Off (Kind of redundant, because I already installed the ADS hassnes first week I got the car)
5). Rear Camera disable distant change from 10M to 30M. Speed at 30KM
6). Enabled Convenience closing with remote
7). Set Rain-Light senor from Sensitive to insensitive
8). Changed auto light position from A & O to A only.
9). Disabled Startup warning message and rear camera warning message
10). Set remote tailgate button from Open and Close
11). Set HU_NBT2 - 3005 Display PIP Info - DIM_VARIANT to OLD for address iDisplay dimming issue


Wish I can code:
1). Instead of change the DIM_Variant to Old model, wish have way to resolve display dimming issue for good, included cluster and HVAC control.
2). Auto parking brake, without using the Auto-H.
3). Set tailgate open from remote that require pressing the key on remote for 5 sec.
4). One touch turn signal from 3 to 5.
5). Rear view camera turn on what parking assist is being use, without putting car in R.
6). Turn down the volumne of PDC sound. It is way too loud.

[weez]

I just ordered OBDLink MX+. Does the app guide you through simple coding? Such as backing up (and how to back up), and how to get the vehicle into coding mode? I assume only the values you drill into are changed if you change a setting and all others are already at factory default?

[titomi]

Originally Posted by weez

I just ordered OBDLink MX+. Does the app guide you through simple coding? Such as backing up (and how to back up), and how to get the vehicle into coding mode? I assume only the values you drill into are changed if you change a setting and all others are already at factory default?

Try this guide: https://bimmercode.app/quick-start-guide/

[RazorX3]

Is it possible to code Carplay in an X3 without ConnectedDrive but has 609 Navigation Professional and Enhanced Bluetooth?

[JayPichardo]

Originally Posted by chris88

Hello

work this on the g01?
open and close the car by walk away. like this https://t1p.de/u4e5


HU_NBT_EVO
3000 HMI - CKT_DOOR_LOCK_UNLOCK - aktiv

BDC_BODY2
3030 KeyManager - CKT_ENABLE - aktiv
3030 KeyManager - CKT_FUNCTIONS - light_unlock_lock

Are you saying that this works?

[lo_cheng]

Is there cheat sheet exist to explain what does each item mean in Expert mode?

[teaston]

Originally Posted by RazorX3

Is it possible to code Carplay in an X3 without ConnectedDrive but has 609 Navigation Professional and Enhanced Bluetooth?

It's not coded, you need an FSC code for it, and a wifi antenna if your car doesn't have wifi hotspot.

[marcati]

Originally Posted by lo_cheng

Is there cheat sheet exist to explain what does each item mean in Expert mode?

No. I asked for this before, even from the manufacturer

[RazorX3]

Originally Posted by teaston

It's not coded, you need an FSC code for it, and a wifi antenna if your car doesn't have wifi hotspot.

But I heard that 2019 production X3 cannot accept USB fsc codes, is it true?

[teaston]

Originally Posted by RazorX3

But I heard that 2019 production X3 cannot accept USB fsc codes, is it true?

I haven't heard anything about that.

You'd need to find a decent BMW retrofitter, I know a great one in the UK but it looks like that won't be much help to you.