06-13-2021, 06:52 PM | #1 |
Private
31
Rep 88
Posts |
Chassis stabilization warning 4x4 ABS
Sorry about the long story. Hope someone can help me on this and help others in the future.
2012 X3 35i 54k miles. This happened yesterday. Right after I started my car put it in drive, "Chassis stabilization warning” with the yellow 4X4 ABS symbol. Message said “drive moderately. Avoid hard braking. Contact or drive to BMW” I pulled over Used bimmerlink to pull error code. It came back with a lot of codes Some that I understand are Under DSC 480686, Wheel speed sensor – approach detection faulty 48068C, Transfer case clutch temp shut down, possibly overheating Under Integrated chassis 480114 D017A3 D017C5 D02C67 Under Transfer box 440117, four wheel distributor gearbox temporarily shut down Under transmission control CF2F02 DSC interface(actual wheel speed HL/VL?HR/VR 0x254) signal invalid Under radar sensor 480512, speed – DFA_EMF frequency overlimit D3AC8D, Signal error(status hydraulic function, id: ST_HYDFN) Sender: DSC_Modul- Qualifier Was able to clear all the codes except those under DSC and Transfer case. Tried to drive the car, it seems to be drivable without suffer any power lost and noise. So I was thinking about it is could be the wheel sensor caused it. Drove the car moderately for around 4 miles to buy something then head home. After the stop, It started right up with the same warning. Scanned it again with about the same error codes. Started to drive home. Within 30 seconds, I feel a cluck and new warning on the dash, it said Transmission malfunction, do not stop engine. Continue driving may not be possible after switch off engine. Due to my situation, I decided to drive home(about 10 miles away). The car ended up in limp mode, idling fine, but felt like I only have the 4th gear. After a very slow drive for 30 mins, finally home. I realized that I cannot shifted off from D( Can’t even go to R, N or P). Since I am home, I have no choice but to shut it down. When I restarted the car, to my surprise, I was able to put it to R. I also don’t have transmission malfunction anymore. Only chassis stabilization with 4 x4 abs symbol. I scanned it again to see anything new. Under transmission 421474, sensor technology: Inadmissible deviation from output speed and wheel speed(actual wheel speed HL/VL/HR/VR, 0x254) within gear shifting or in a non-positive state CF2F02, DSC interface(actual wheelspeed HL/VL/HR/VR, 0x254)signal invalid Under transfer case, 44011C, Powertrain protection deviated 440117, four wheel distributor gearbox temporarily shut down. BTW, Bimmerlink said that my transmission temp at 227 degrees.(wonder if I damage my transmission) Do you think the wheel sensor causing all these?? |
01-17-2022, 01:43 PM | #4 |
Registered
0
Rep 2
Posts |
Hi,
New to the forum. not sure if I shd post my question here or start a new thread. Encountered this today and wondering how to resolve. TCM-Transmission Control Module -egs 48068C : Transfer box: Temporary fault, temparature 4809b0: wheel speed sensor, drive off recognition, front left reg... |
Appreciate
0
|
01-22-2022, 04:14 AM | #5 | |
Private First Class
39
Rep 135
Posts |
Quote:
are your tires inflated at the right pressure? are your wheels oem and properly balanced? |
|
Appreciate
0
|
01-23-2022, 07:11 PM | #6 |
New Member
5
Rep 8
Posts |
I got the same error earlier today on a 2015 X3 28i with 85K miles. Along with it I also got several others like parking brake error, abs , restraint error etc. I should have taken a picture. The GPS started acting weird and showed that I was driving off the road. I drove the car in limp mode for a couple of miles until I could stop at a gas station. I switched off the car completely and waited for a couple of minutes and restarted it. All of the errors disappeared! I was able to drive about 125 miles back home with out any issues. I will have to take it to the local dealer and find out what happened.
|
Appreciate
0
|
05-18-2024, 05:24 PM | #8 | |
Registered
0
Rep 1
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|