[BuiltMyWay]

I wanted to share my build because it was possible with this forum. I finished it when I didn't want to add anything else. I wanna thank everyone who helped out. At the end, I barley drove it because I traded it in early.
Feel free to PM me any questions or if you want anything for cheap or check the classifieds.

Here’s the breakdown:

Exterior:
-Xpel nano-ceramic tint
-MSS Lowering springs
-21” HRE P101SC forged monoblock wheels in F 265/40 R 295/35R + TPMS (initially had H&R spacers, tried different setups of 15mm front and 15mm/20mm rear on stock wheels)
-Wrapped front and rear reflectors body color, light tint front and rear lights, black spoiler, body color strut bar and v-bar, & blacked out the chrome rings on emblems
-Sterckenn carbon front lip
-Autotecknic carbon grill
-Autotecknic carbon eyelids
-Autotecknic carbon splash guards
-Autotecknic gas cover
-Carbon side skirts
-M performance tailfins

Performance:
-RVG catless downpipe
-Evolution racewerks catless midpipe
-Dinan axel back exhaust
-RK tunes front mount intakes
-BM3 + Custom tune
-NGK spark plugs gaped
-Racechip XLR (didn't use because of custom tune)

Interior:
-Bavsound full package (speakers and underseat subs)
-Autotecknic black paddle shifters
-E-sys programming
-EU oem ceramic control
-EU oem ceramic iDrive touch controller

[95wildtt]

Originally Posted by BuiltMyWay

I wanted to share my build because it would not have been possible without this forum. Initially, I just wanted to tint and lower it, but it continued until I didn't want to add anything else. I learned a lot, especially from the guys here, and wanna thank everyone who helped out. At the end, I barley drove it because I traded it in early. Feel free to pm me if you want anything for cheap or for any questions about the mods.

Here’s the breakdown:

Exterior:
-Xpel nano-ceramic tint
-MSS Lowering springs
-21” HRE P101SC forged monoblock wheels in F 265/40 R 295/35R + TPMS (initially had H&R spacers, tried different setups of 15mm front and 15mm/20mm rear on stock wheels)
-Wrapped front and rear reflectors body color, light tint front and rear lights, black spoiler, body color strut bar and v-bar, & blacked out the chrome rings on emblems
-Sterckenn carbon front lip
-Autotecknic carbon grill
-Autotecknic carbon eyelids
-Autotecknic carbon splash guards
-Autotecknic gas cover
-Carbon side skirts
-M performance tailfins

Performance:
-RVG catless downpipe
-Evolution racewerks catless midpipe
-Dinan axel back exhaust
-RK tunes front mount intakes
-BM3 + Custom tune
-NGK spark plugs gaped
-Racechip XLR (didn't use because of custom tune)

Interior:
-Bavsound full package (speakers and underseat subs)
-Autotecknic black paddle shifters
-E-sys programming
-EU oem ceramic control
-EU oem ceramic iDrive touch controller

Looks beautiful, great job!!

Where did you get the CF rear wheel arch pieces, guessing they are the M Performance tailfins, so from M Performance?
Did you tint your taillights, they look darkened a bit...??

[BuiltMyWay]

Hey man, they're for the autotecknic splash guards for x3m. They could be installed on the x4 by making a hole in the fender where the clip that'll hold it in place (along with double-sided tape) goes. There is a machine that shoots clips like a nail gun.
Yeah M performance tailfins. It's oem in europe. https://www.getbmwparts.com/oem-part...b3J5IFBhZ2U%3D
Yeah it's the lightest vinyl wrap, like a light smoke. I did it be because the color was overall darker and the lights stood out too much.

[95wildtt]

Originally Posted by BuiltMyWay

Hey man, they're for the autotecknic splash guards for x3m. They could be installed on the x4 by making a hole in the fender where the clip that'll hold it in place (along with double-sided tape) goes. There is a machine that shoots clips like a nail gun.
Yeah M performance tailfins. It's oem in europe. https://www.getbmwparts.com/oem-part...b3J5IFBhZ2U%3D
Yeah it's the lightest vinyl wrap, like a light smoke. I did it be because the color was overall darker and the lights stood out too much.

I tinted my tails too, just didn't like the bright red with the TRM color.
May look at the Tail Fins, they look pretty cool... assume they are just taped on the glass?

Thanks!

[BuiltMyWay]

Originally Posted by 95wildtt

I tinted my tails too, just didn't like the bright red with the TRM color.
May look at the Tail Fins, they look pretty cool... assume they are just taped on the glass?

Thanks!

Yeah, it's a glue that comes with it. There is no removing it, but it looks very natural. No one knew it was an add-on

[MADBMWX5MC]

OP, well done. Thx for sharing...looking great!

[BuiltMyWay]

Originally Posted by MADBMWX5MC

OP, well done. Thx for sharing...looking great!

Thanks man!

[Bee Pee]

Ditto - yr car looks great.

What height settings did you go for with MSS HAS ?

[BuiltMyWay]

Originally Posted by Bee Pee

Ditto - yr car looks great.

What height settings did you go for with MSS HAS ?

Thanks man. I had it as low as it could go without riding on the bump stops.

[Bee Pee]

Originally Posted by BuiltMyWay

Thanks man. I had it as low as it could go without riding on the bump stops.

Installing MSS soon.
Please share or DM measurements F&R of wheel center upto fender at 12 o clock so as I have some reference dimensions to work to when adjusting the cars ride height after install. Thanks in advance