[sneesh]

Originally Posted by sd306

there isn't an issue right now for BM3 or MP that I am aware of - even with the latest updates. It also depends on dealer updates and your individual car versions. For example, if you have service tomorrow and they have an update to block OBD flashing for tuners, then I won't have it until I go in for service and even then if i do go in, it depends if they actually flash that update (some dealers you can ask them not, but then that hints at a tune ).

From MP's website:
https://missiontuning.com/bmw-engine...lash-tune.html
"*At the current moment, all S58s are flashable over OBD, including the latest 2020-03 dealer update."

i went in for break in service not too long ago i don't think they updated as i had both the exhaust valve and ads fused pulled and when i got it back it was still out however my trip was reset, so i'm not quite sure if they did or did not

[GT500R]

Originally Posted by sneesh

i went in for break in service not too long ago i don't think they updated as i had both the exhaust valve and ads fused pulled and when i got it back it was still out however my trip was reset, so i'm not quite sure if they did or did not

Could always call them and ask what was done. It sounds like they might have done something with an update.

[sd306]

Originally Posted by sd306

Just got the MP e50 tune

I'm currently running BM3 E30 OTS. I'll let everyone know how what the butt dyno says.

Quick, initial thoughts. Yeahhhhh buddy! Quicker top end, can hear turbos spool sooner, and launches quicker.

[AlexFL]

Originally Posted by sd306

Quick, initial thoughts. Yeahhhhh buddy! Quicker top end, can hear turbos spool sooner, and launches quicker.

can you get dyno?

[GT500R]

Originally Posted by sd306

Quick, initial thoughts. Yeahhhhh buddy! Quicker top end, can hear turbos spool sooner, and launches quicker.

Yeahhhhhh buddy! Get em!

[sd306]

Originally Posted by AlexFL

can you get dyno?

I probably won't dyno it as the butt dyno says it's quicker and that's all I was looking for Burble is also much stronger and I didn't get the "extra" burble option.

I'll probably throw up some dragy times like GT500R once I test and log some more.

[sd306]

1st try on launch control. Full weight including spare, extra water (gallon), and a few other road trip goodies. All 4 wheels spinning after launch.

Specs:
-2020 X4M Non-Comp
-Stock plugs re-gapped to .024"
-Mission Performance Stage 1 E50 Tune running E53 mix (guessed, didn't test the fuel).
-Stock tire size (265 rear/255 front) on 21" stock wheels.
-15mm rear spacers, 12mm front spacers
-200 miles Michelin Pilot Sport 4S on the rear and 10K miles Continental sport 6 on the front (still decent tread).
-unprepped private concrete road that had minor ups, downs, and turns.
- just over half tank of fuel

BM3 OTS Stage 1 E30 best time was 3.22s after a few tries and weight reduction on Continental sport 6 tires (no spare or any trunk stuff).

Used BM3 Wifi agent to log the whole launch (disregard tune name in the file):
https://www.bootmod3.net/log?id=5fd4...0b43638aeb6013

Based on the timing, i'm going to be adding more ethanol since I didnt verify the ethanol content before filling up.

Another log (looks cleaner) that has nothing to do with the 0-60 or 1/4 mile. Just a random WOT log (disregard tune name in the file):
https://www.bootmod3.net/log?id=5fd4...729b73389aef69

[AlexFL]

Did you guys gap the plugs to 0.025" or left them stock?

[sd306]

Originally Posted by AlexFL

Did you guys gap the plugs to 0.025" or left them stock?

I have another post about this called "tuned and spark plugs". However, stock came gapped at .029"-.030". I regapped the existing stock plugs to .024". Logs were cleaner for BM3 and change was necessary for stronger MP tune.

[sd306]

I have more logs coming just need to burn up this current tank then verify ethanol content at fill up for 93 and e85.

[AlexFL]

Originally Posted by sd306

I have more logs coming just need to burn up this current tank then verify ethanol content at fill up for 93 and e85.

Get the fuel-it ethanol sensor. It was a game changer for me. No more manual ethanol content checks.

[sd306]

Originally Posted by AlexFL

Get the fuel-it ethanol sensor. It was a game changer for me. No more manual ethanol content checks.

Yeah trying to stop spending money, then AlexFL comes along again. I had it in my old car

[AlexFL]

If you MP E50 guys get a chance to log, can you please share the link? Curious to see the target boost pressure on your tune.

[sd306]

Originally Posted by AlexFL

If you MP E50 guys get a chance to log, can you please share the link? Curious to see the target boost pressure on your tune.

I posted some above, still trying to run through the remaining of this tank.

[AlexFL]

Originally Posted by sd306

I posted some above, still trying to run through the remaining of this tank.

Thank you!

[sd306]

Originally Posted by sd306

Yeah trying to stop spending money, then AlexFL comes along again. I had it in my old car

AlexFL

I took some new logs, but the ethanol is too high per Mission Performance. Got the ethanol sensor on the way, but going to reduce my ethanol from ~57 to ~50 and will verify when the sensor gets here. Then post up new logs.

[FSociety]

Originally Posted by sd306

AlexFL

I took some new logs, but the ethanol is too high per Mission Performance. Got the ethanol sensor on the way, but going to reduce my ethanol from ~57 to ~50 and will verify when the sensor gets here. Then post up new logs.

Avoid Fuel-It, get the Spool performance sensor instead
or Dane K can you hook up with his Custom One

[AlexFL]

Originally Posted by FSociety

Avoid Fuel-It, get the Spool performance sensor instead
or Dane K can you hook up with his Custom One

Why avoid Fuel-it?

[sd306]

Originally Posted by AlexFL

Why avoid Fuel-it?

Fuel-It has been awesome for me. But won't continue here as this is all MP tune related.

[sd306]

Originally Posted by sd306

AlexFL

I took some new logs, but the ethanol is too high per Mission Performance. Got the ethanol sensor on the way, but going to reduce my ethanol from ~57 to ~50 and will verify when the sensor gets here. Then post up new logs.

Fuel-It analyzer came in, got logging setup with MHD monitor license so I can log on my iPhone still

Here is a log with e49. I just floored it in 2nd gear to 3rd gear:
https://datazap.me/u/sd306/log-16106...6-37-38&solo=5

Looks good to me, may run a bit lean after first flooring it until it gets to higher RPM but im no expert.

[AlexFL]

Originally Posted by sd306

Fuel-It analyzer came in, got logging setup with MHD monitor license so I can log on my iPhone still

Here is a log with e49. I just floored it in 2nd gear to 3rd gear:
https://datazap.me/u/sd306/log-16106...6-37-38&solo=5

Looks good to me, may run a bit lean after first flooring it until it gets to higher RPM but im no expert.

what’s your 60-130?

[sd306]

Originally Posted by AlexFL

what’s your 60-130?

Actually haven't officially timed it. Will try to here soon.