[nyalpine90]

i been reading this thread looking for list of options that were possible to code.
i had my x3 coded last night

key fob fold and unfold mirrors, 1 touch window close
remove disclaim
seatbelt chime
mph on cluster
temp on tire
fog light turn when unlock
DRL for rears
welcome M screen,

[mop75]

Hi Shawn!
I have the need to delete the amber corner lights of my X3 F25 in order to have my car compliant with the EU regulation.
I've just ordered the cable but I need all the stuff to continue.
Can you help me out sending me what I need?

Many Thanks

[shawnsheridan]

Originally Posted by mop75

Hi Shawn!
I have the need to cancel the amber corner light of my X3 F25 in order to have my car compliant with the EU regulation.
I've just ordered the cable but I need all the stuff to continue.
Can you help me out sending me what I need?

Many Thanks

PM sent.

[Tangsta]

Hi Shawn,

Can you PM me a link to the latest E-Sys / launcher and psdzdata? Assuming it's backwards compatible with my 2013 F25 (CIC).

I've been playing around with coding on and off for a while... just VO coded 2TB yesterday and when I started poking around FDL afterwards it asked for a PIN. Can't remember what I did when it asked for that before, but good excuse for me to upgrade versions.

Thanks!

[shawnsheridan]

Originally Posted by Tangsta

Hi Shawn,

Can you PM me a link to the latest E-Sys / launcher and psdzdata? Assuming it's backwards compatible with my 2013 F25 (CIC).

I've been playing around with coding on and off for a while... just VO coded 2TB yesterday and when I started poking around FDL afterwards it asked for a PIN. Can't remember what I did when it asked for that before, but good excuse for me to upgrade versions.

Thanks!

PM sent.

[FloridaX4]

Could you PM me what I need as well.

Thank you

[JohnAG]

I did more coding and discovered that adding the signal light signal to the HUD is not working. Did anyone else have this same issue? I mean the default value were changed to the desired value, but not getting the desired result.

P.S. I was able to make changes such as deleted the disclaimer notice at start up and made it so that the doors unlocked when the ignition is turned off. The weird thing is that I also activated the "M" logo to come on during start up, but that went away when I disabled the disclaimer notice.

[shawnsheridan]

Originally Posted by FloridaX4

Could you PM me what I need as well.

Thank you

PM sent.

[zalagan]

Hi Shawn - I've got a 2015 XLine X3 and would like to code a few things - could you PM me the latest info to get started

Many thanks
David

[shawnsheridan]

Originally Posted by zalagan

Hi Shawn - I've got a 2015 XLine X3 and would like to code a few things - could you PM me the latest info to get started

Many thanks
David

PM sent.

[Sarsippius3rd]

Hi Shawn, I have been interested in coding my F26. Can you please PM me details on what I need? Thanks in advance!

[shawnsheridan]

Originally Posted by Sarsippius3rd

Hi Shawn, I have been interested in coding my F26. Can you please PM me details on what I need? Thanks in advance!

PM sent.

[danend]

I've coded my X5 E70, but would like to start coding my 2013 X3 F25. Please send me the info to get started. Thanks in advance!

[shawnsheridan]

Originally Posted by danend

I've coded my X5 E70, but would like to start coding my 2013 X3 F25. Please send me the info to get started. Thanks in advance!

You will need an ENET cable as your DCAN Cable won't work.

PM sent.

[dieselgg]

Hi Shawn,

If I just want to read and clear fault codes for the F25, is all that I need is INPA? If so, what version do I need and is there a link available for that?

From what I have read, the Tool32 module is what is used for clearing error codes and it is part of INPA.

[shawnsheridan]

Originally Posted by dieselgg

Hi Shawn,

If I just want to read and clear fault codes for the F25, is all that I need is INPA? If so, what version do I need and is there a link available for that?

From what I have read, the Tool32 module is what is used for clearing error codes and it is part of INPA.

If you just want to clear fault codes, you can use E-Sys or Tool32. If you want to read and interpret them in any meaningful way, then you need ISTA/D (Rheingold). INPA is a little of both, but mostly all German.

[dieselgg]

Shawn,

I have INPA/EDIABAS 6.4.7 and 5.02 with a K+DCAN USB interface. And I have the F25 ECU .prg files. Will this allow me to read and clear codes on the X3 (F25)?

[shawnsheridan]

Originally Posted by dieselgg

Shawn,

I have INPA/EDIABAS 6.4.7 and 5.02 with a K+DCAN USB interface. And I have the F25 ECU .prg files. Will this allow me to read and clear codes on the X3 (F25)?

You need an ENET Cable, not K+DCAN. But again, I don't recommend INPA myself.

[RaslDasl]

After 4 plus months driving my 2016 F25 I'm ready to start coding.

I have the e-net cable (bought it while waiting to pick up the car) and some software the cable seller sent. Since it was a few months ago I'm not sure I have the latest stuff.
E-Sys 3.26.1
E-Sys Launcher (I seem to be in a 2-day waiting period to select series)
v.55.4_PSdZData_Lite

Do I need anything newer or is this all good?

Also, my #1 task is to code the anti-dazzle and VLD back on for my LEDs. There are tons of cheat sheets and instructions but almost too many. Does anyone have a cheat sheet or instructions they have used on an LCI F25 to do this coding?

Thanks in advance.

[shawnsheridan]

Originally Posted by RaslDasl

...v.55.4_PSdZData_Lite

Do I need anything newer or is this all good?
...

As long as car has 55.4 or older on it, then it is good, but I would just update, as you should use latest E-Sys Launcher.

PM sent.

[dieselgg]

Hi Shawn,

I managed to find an old copy of E-sys. It is version 3.18 with PSDZ version 47.5 Is this enough to get clear codes on a 2011 X3 (F25 chassis)?

Also is Tool32 part of this installation?

And I looked in the EDIABAS\ECU installation folder and I don't see the F25 .prg files. Do I have to copy the F25 project files that I have from a separate zip file into this folder?

Thanks in advance,

[shawnsheridan]

Originally Posted by dieselgg

Hi Shawn,

I managed to find an old copy of E-sys. It is version 3.18 with PSDZ version 47.5 Is this enough to get clear codes on a 2011 X3 (F25 chassis)?

Also is Tool32 part of this installation?

And I looked in the EDIABAS\ECU installation folder and I don't see the F25 .prg files. Do I have to copy the F25 project files that I have from a separate zip file into this folder?

Thanks in advance,

It should be good to clear codes, but not much else.

If you have EDIABAS folder, than you have Tool32 in the \BIN folder. Use F01.prg to clear codes.