[walendvay]

Can I get a copy of the goods? I want to get in on the coding fun.

[shawnsheridan]

Originally Posted by walendvay

Can I get a copy of the goods? I want to get in on the coding fun.

PM sent.

[RhoXS]

Last January I downloaded PSdZData Lite Ver 51.3 and E-Sys ver 3.24.3 but then got distracted by other things and did nothing else.

Please help with three questions:

1-Are both these sets of files still valid?

2-What is a recommended reliable and trusted source to buy a cable?

3-What is a source to buy the required token?

I am only going to recode only two parameters; TPM to show pressure & temp & the digital MPH display. If there was someone experienced convenient in central NY I would probably just ask them to help but there does not appear to be so I am going to do it myself.

[shawnsheridan]

So long as your car has <= 51.3 on it, yes, they are still valid.

PM sent for cable and Token solution options.

[RogerR]

My 2015 X3 28i is a week old. Super super. But the Blind Spot monitor is set up to work only after the turn signal is pressed. Set up for imbeciles.

HOWEVER once in Stop and Go Adaptive Cruise mode (new in '15 in the X3 a fantastic application everyone should get) the Blind Spot Indicator works as it should, i.e., whenever a vehicle enters the blind spot area it lights. No turn signal activation needed.

QUERY. Is there a Code change that will bypass the turn signal requirement when not in Cruise Control mode. In other words making active blind spot monitoring the default.

Thanks.

[RhoXS]

It has been my understanding it is best the engine is running so battery capacity is not challenged. The instructions at the beginning of this thread state:

Connect E-Sys to your Car:
1.Connect ENET cable between car's OBD port and network port of laptop.
2.Switch on the ignition of the car, don't start the engine.
3.You will notice laptop tries to connect ....

So, when is it OK to start the engine?

[shawnsheridan]

Those are very old Instructions.

Start motor, connect cable to car and then laptop, wait until laptop gets IP Address, and then launch E-Sys.

[Magwich]

Shawn, Can I please get a link to the software? Thank you.

[RhoXS]

Shawn, thank you for the quick reply.

[shawnsheridan]

Originally Posted by Magwich

Shawn, Can I please get a link to the software? Thank you.

PM sent.

[RogerR]

Can I get into the coding fun. Getting the PM. Thanks.

[shawnsheridan]

Originally Posted by RogerR

Can I get into the coding fun. Getting the PM. Thanks.

PM sent.

[RhoXS]

I was surprised when I noticed the speedometer reading exactly matched a handheld GPS reading. That made me think the speedometer uses the GPS for speed input. Is this indeed so or just coincidence?

I was just doing some Google searches for a parameter to extend or eliminate the rear window heater time to off delay when I stumbled into the following two items available on the one series.

True speed in digital speedometer KOMBI BC_DIGITAL_V_KORREKTUR nicht_aktiv = true speed
True speed in analog speedometer KOMBI BC_V_KORRECTUR nicht_aktiv = true speed

Does anyone know if these parameters exist on the F25?

I am waiting for my cable to arrive so I can activate the TPM pressure/temps and digital speed indication. It would be nice if both the digital and analog speedometer read the accurate speed from the GPS.

[shawnsheridan]

BC_V_KORREKTUR should be there, but not BC_DIGITAL_V_KORREKTUR.

[aquamaster]

Hi Guys,

Thanks for heaving me on this forum.

I'm getting ready to receive my 3.0d X3 F25 in 10 days, prod. date 28-10-2013.
The car was in stock so I have no involvement about original configuration. Since it's built in with S609A Navigation system Professional and S6NHA Hands-free with USB interface ONLY , I would like to try coding it for streaming wireless audio/enhanced Bluetooth if possible.
I have not seen the car yet then I don't know if there is any combox built in.
Already read pretty much all the posts regarding coding 6NH to 6NR or similar, but not to sure where about to order the ENET cable (OBD II ?), where to find E-SYS software 3.24.3 with EST token and Pin, psdzdata 52.2,
Do I need a retrofit unit or not, considering year of built (HU_CIC or HU_NBT) ? Some of you are saying that if 6NH is built in, there is no combox in the car?!
Any help, advice or PM is much appreciated, thank you.

[shawnsheridan]

Originally Posted by aquamaster

Hi Guys,

Thanks for heaving me on this forum.

I'm getting ready to receive my 3.0d X3 F25 in 10 days, prod. date 28-10-2013.
The car was in stock so I have no involvement about original configuration. Since it's built in with S609A Navigation system Professional and S6NHA Hands-free with USB interface ONLY , I would like to try coding it for streaming wireless audio/enhanced Bluetooth if possible.
I have not seen the car yet then I don't know if there is any combox built in.
Already read pretty much all the posts regarding coding 6NH to 6NR or similar, but not to sure where about to order the ENET cable (OBD II ?), where to find E-SYS software 3.24.3 with EST token and Pin, psdzdata 52.2,
Do I need a retrofit unit or not, considering year of built (HU_CIC or HU_NBT) ? Some of you are saying that if 6NH is built in, there is no combox in the car?!
Any help, advice or PM is much appreciated, thank you.

Your car with 609 should have NBT Head Unit, which has builtin Combox.

Just follow my instructions here to code EBT:

http://www.f30post.com/forums/showpo...65&postcount=9

PM sent.

[aquamaster]

Thank you for PM and reply Shawn. I'll keep you updated about my experience soon. Now I'm ordering the cable

[RichardBR]

Hi guys. I might have missed it, but is there an up-to-date cheat sheet of all the Secret twigs that can be coded?


Richard

[mariusz4567]

Hi Guys,
Is it possible replacement regular controller on iDrive touch, have navi NBT in 2014.
What do I coding
Thanks

[shawnsheridan]

You have regular controller, and want to replace it with Touch Controller?

[mariusz4567]

I have regular controller
Sorry for my English translator

[shawnsheridan]

You need to replace the Contoller, add / wire in the Handwriting Module, and then Code NBT:

ZBE_TOUCH = aktiv
ZBE_TOUCH_BROWSER = aktiv
ZBE_TOUCH_INTERACTIVE_MAP = aktiv
ZBE_TOUCH_SPELLER= aktiv