[temoore48]

Thanks, Shawn.

[jeanproy]

I've just been updated to F025-15-07-501. Does anybody have the link to download P3.56.0?

[shawnsheridan]

Originally Posted by jeanproy

I've just been updated to F025-15-07-501. Does anybody have the link to download P3.56.0?

Have you tried to read car with 55.4?

[jeanproy]

Yes Shawn, I can connect to the car but when I try to read coding data from the CAFD, I receive an error message.

Guess, I'll have to wait for the next psdzdata version

[shawnsheridan]

Originally Posted by jeanproy

Yes Shawn, I can connect to the car but when I try to read coding data from the CAFD, I receive an error message.

Guess, I'll have to wait for the next psdzdata version

PM sent.

[jeanproy]

Wow, thanks a lot for the quick reply. I don't know where you get all this stuff but you're so effective.

[TonyX3driver]

Originally Posted by TonyX3driver

Ok, will go on and let you know

Shawn, just finished with power tailgate retrofit HW. All wired, mounted.
Battery connected and- it works!!!
Without programming it working just like this, except:
- No setting height possibility menu on CIC.
- Front cabin button is not working at all.
Next days when time I will connect E-sys to check what I will see there.

[shawnsheridan]

Originally Posted by TonyX3driver

Shawn, just finished with power tailgate retrofit HW. All wired, mounted.
Battery connected and- it works!!!
Without programming it working just like this, except:
- No setting height possibility menu on CIC.
- Front cabin button is not working at all.
Next days when time I will connect E-sys to check what I will see there.

Nice. Need to add the Power Liftgate option, 316 or whatever it is for F25, and then VO code HKFM.

[rwgreg]

Hi Shawn, if possible can you pm me a link to e-sys etc. please. I have F25 2012 with 609+508 and want to fit rear cam retrofit. I believe it should be VO FA 3AG active but still learning. Any tips welcomed.
Many thanks.
Ron

[shawnsheridan]

Originally Posted by rwgreg

Hi Shawn, if possible can you pm me a link to e-sys etc. please. I have F25 2012 with 609+508 and want to fit rear cam retrofit. I believe it should be VO FA 3AG active but still learning. Any tips welcomed.
Many thanks.
Ron

Yes, add 3AG to FA and VO Code TRSVC, PDC, and HU_CIC.

PM sent.

[TonyX3driver]

Originally Posted by shawnsheridan

Nice. Need to add the Power Liftgate option, 316 or whatever it is for F25, and then VO code HKFM.

Hi Shawn,
316 adde to SALAPA, FA written to the car. Before it, CAFD was not visible. After this I have CAFD_000007CB_006_004_000.
I can open and change values, but there is not any functional change- i.e. all is working like before, and my front cabin button TOEHKI is not functional. Also don't know what function name to activate CIC screen with height opening limit.
Any thougthts??

[TonyX3driver]

Originally Posted by TonyX3driver

Hi Shawn,
316 adde to SALAPA, FA written to the car. Before it, CAFD was not visible. After this I have CAFD_000007CB_006_004_000.
I can open and change values, but there is not any functional change- i.e. all is working like before, and my front cabin button TOEHKI is not functional. Also don't know what function name to activate CIC screen with height opening limit.
Any thougthts??

photos:
origin


during the flash


after

[rwgreg]

Originally Posted by shawnsheridan

Yes, add 3AG to FA and VO Code TRSVC, PDC, and HU_CIC.

PM sent.

Wonderful and many thanks for the additional instructions.

[shawnsheridan]

Originally Posted by TonyX3driver

Hi Shawn,
316 adde to SALAPA, FA written to the car. Before it, CAFD was not visible. After this I have CAFD_000007CB_006_004_000.
I can open and change values, but there is not any functional change- i.e. all is working like before, and my front cabin button TOEHKI is not functional. Also don't know what function name to activate CIC screen with height opening limit.
Any thougthts??

So you can FDL Code HKFM now with no errors?

Did you allow for an hour before testing the closing functionality?

[CostinLogin]

Hello again! After a long absence in wich i've been reading and doing only about FSC codes I thought I finaly do some coding on my X3. But I came across with the problem from the picture below when I tried to save CAFD files. Does anyone have any ideea what is missing in there? Thanks in advance.

[shawnsheridan]

Originally Posted by CostinLogin

Hello again! After a long absence in wich i've been reading and doing only about FSC codes I thought I finaly do some coding on my X3. But I came across with the problem from the picture below when I tried to save CAFD files. Does anyone have any ideea what is missing in there? Thanks in advance.

You need to update your PSdZData. PM sent.

[TonyX3driver]

Originally Posted by shawnsheridan

So you can FDL Code HKFM now with no errors?

Did you allow for an hour before testing the closing functionality?

yes, Coding with no errors on the end window mesage. Checked button again this morning- no change.
So let]s make summary until now:
1. Mounted all hardware and wired according to schematics (those printed out from similar car with original 316).
2. Battery connected and all starts worked automatically, except front cabin button (in schematics named TOEHKI and connected to A16 CAS connector A16*1B pin39.
3. On CID no menu screen for opening height limit.
4. Ater this option 316 added to SALAPA and FA written to the car. No any outgoing effect.

Questions- Can I be sure that new FA changed something inside the car?? How to verify, that FA is correctly updated?
I don't know what code value enable CID screen?

Thank you for help.

[shawnsheridan]

Originally Posted by TonyX3driver

yes, Coding with no errors on the end window mesage. Checked button again this morning- no change.
So let]s make summary until now:
1. Mounted all hardware and wired according to schematics (those printed out from similar car with original 316).
2. Battery connected and all starts worked automatically, except front cabin button (in schematics named TOEHKI and connected to A16 CAS connector A16*1B pin39.
3. On CID no menu screen for opening height limit.
4. Ater this option 316 added to SALAPA and FA written to the car. No any outgoing effect.

Questions- Can I be sure that new FA changed something inside the car?? How to verify, that FA is correctly updated?
I don't know what code value enable CID screen?

Thank you for help.

Try also coding CIC and ICM.

You can use .NCD / CAFD Tool, and compare .NCD files from ECU coded with 316 and without so see what FDL's have been chnaged:

http://www.bimmerfest.com/forums/sho...d.php?t=749668

[TonyX3driver]

Originally Posted by shawnsheridan

Try also coding CIC and ICM.

You can use .NCD / CAFD Tool, and compare .NCD files from ECU coded with 316 and without so see what FDL's have been chnaged:

http://www.bimmerfest.com/forums/sho...d.php?t=749668

Ok, thank you.
Will check it out and come back later

[TonyX3driver]

Originally Posted by TonyX3driver

Ok, thank you.
Will check it out and come back later

So I was able to find:
HU_CICHB > EXBOX 3001 > BACKDOOR_OPENINGANGLE = aktiv
Now height limit setting screen is active.
But still not able to find anything about TOEHKI button.
Button is connected to CAS, but cannot find any value to wake it up.
I believe something is wrong with my coding procedure-
Now I'm chenging all values manually- select known function and change value.
But, correct me if I'm wrong- If I add option 316 to SALAPA, it must update all related ECU's at once for full functionality. How to do this exactly? By TAL??
If I'm there, I don't know what to check in boxes there. Afraid to do something wrong.
I believe I flashed HKFM, I see CAFD, but other ECU's values not changed to work properly with HKFM.

I'm slightly getting lost in this
Can you help a little??

[shawnsheridan]

Originally Posted by TonyX3driver

So I was able to find:
HU_CICHB > EXBOX 3001 > BACKDOOR_OPENINGANGLE = aktiv
Now height limit setting screen is active.
But still not able to find anything about TOEHKI button.
Button is connected to CAS, but cannot find any value to wake it up.
I believe something is wrong with my coding procedure-
Now I'm chenging all values manually- select known function and change value.
But, correct me if I'm wrong- If I add option 316 to SALAPA, it must update all related ECU's at once for full functionality. How to do this exactly? By TAL??
If I'm there, I don't know what to check in boxes there. Afraid to do something wrong.
I believe I flashed HKFM, I see CAFD, but other ECU's values not changed to work properly with HKFM.

I'm slightly getting lost in this
Can you help a little??

After you add 316 you must VO Code all related ECU's by right-click => code on each one. You do not make TAL for this.

HKFM is the one module where coding changes require car to go to sleep (1 hour) before changes kick in, so testing FDL Codes involves a lot of waiting.

[hkjarral]

Can somebody please send me a link to buy cable and pm me softwares required.

And is there any new step by step guide like 1st post or the same guide should still work ?

Thanks in Advance