05-02-2012, 08:52 PM | #1 |
Private
11
Rep 73
Posts |
How to remove kidney grille on F25 for painting
Hi guys,
So after about two weeks with my 2013 X3 I wasn't fully satisfied with black grille they changed for 2013 figured that to buy 2 would cost me about $210 (in US) so I decided to paint it. There are few good guides on how to remove kidney grille, but none for X3 F25 so while I used other guides to remove it I decided to create one. This is what it looks in black: Some other guides: X1 Guide X3 short overview Another informative guide Tools I used: Angle tool Multiple small screwdrivers Torx T30 Paint: Rust-oleum Universal Metallic Dark Steel (picked from 4 different colors) Note: I don't have jetwashers so in case you do, please refer to a guide above for X1, but explains what to do with jetwashers. 1. Start by removing rubber that covers screw heads - you just pull it towards the engine and it comes out. It's not glued or anything. Then use T30 torx to remove 6 screws from the top of the bumper. 2. To remove the grille you have carefully pull the bumper towards you and use long screwdriver to unlock the clips that holding grille. I did it in the order shown on the picture. After you unlocked 1-5 use right angle tool to unlock 6-8. It can be somewhat tricky and it's the hardest part of the whole process, but it took me about 10 minutes to remove both grilles. 3. After you popped them out it's time to take black inserts from the frame. There are few steps I took in order to do that. Since there are quite a few locks it's been very heplful for me to use small screwdrivers and some tools to keep them unlocked. After I did that it was easy to unlock it from the bottom and remove black inserts. 4. I tried multiple paints on some ground anchors just to see which one will look better on the grille. I picked Rust Oleum Universal Metallic Dark Steel And painted both grilles. I added probably 5 layers or so. I figured, it's easier to add multiple thin layers than one thick. Also, have some Goo Gone and paper towel handy in case you have some places with thicker paint. Just softly remove it from the grille, make sure not to rub too hard, otherwise you'll see imperfections later. I let it dry for a few hours and after I could touch it I got inserts in the frame (easy, just pop them inside) and insert grilles inside the bumper (just like you saw in Megafactories). So here are some final results: Thanks for reading, I hope it was helpful! Last edited by stactum; 05-02-2012 at 10:22 PM.. |
05-02-2012, 09:59 PM | #2 |
Private
7
Rep 86
Posts |
Very cool, looks sweet. I much prefer that look over the black.
Just one thing to note - I hate imageshack, it has popups (I just got one to "f***sexygirls.com" or something similar. |
Appreciate
0
|
05-03-2012, 07:12 AM | #3 |
Captain
72
Rep 876
Posts |
Man, those look great, thanks for sharing!!
I didn't realize the 2013 models got black grills. Funny. Ours look almost exactly like yours after painting. I have been wanting to switch ours over to black. Haven't gotten around to it yet. We could have just traded!! ;-) |
Appreciate
0
|
05-03-2012, 08:18 AM | #4 | |
Private
7
Rep 86
Posts |
Quote:
__________________
Current drive: 2018 M2 Competition DCT, Sunset Orange
Previous: BMW X3 xDrive 30d |
|
Appreciate
0
|
05-03-2012, 08:05 PM | #5 |
Major
625
Rep 1,093
Posts
Drives: 2021 X3 M40i
Join Date: Feb 2012
Location: CA
|
That is an amazing job. I prefer the silver/titanium as well.
That being said, many people actually pay to make it black, so it would be nice if dealerships facilitated an exchange. |
Appreciate
0
|
05-03-2012, 09:10 PM | #6 |
First Lieutenant
176
Rep 360
Posts
Drives: 1M; E90 M3 ZCP; M4 GTS
Join Date: Jul 2011
Location: Minneapolis, MN
|
Sad, but true. Paid to go with "BMW Performance" grilles on my 1M...i.e. all black. Would probably trade my titanium grilles on the X3 for the new 4 cylinder setup..I waffle back and forth on that one.
__________________
-kskpsu
|
Appreciate
0
|
08-09-2012, 10:53 AM | #7 | |
New Member
2
Rep 19
Posts |
Quote:
|
|
Appreciate
0
|
10-01-2012, 11:31 AM | #9 |
Second Lieutenant
20
Rep 201
Posts |
|
Appreciate
0
|
10-01-2012, 01:08 PM | #11 |
Captain Unsensible
99
Rep 737
Posts
Drives: 2016 M240i Coupe - Estoril
Join Date: Sep 2011
Location: United Kingdom
|
I used an allen key that had a right angle to get the 2 I couldn't get to with my finger
|
Appreciate
0
|
10-02-2012, 09:56 AM | #13 |
Private
9
Rep 85
Posts
Drives: 2022 X3 M40i
Join Date: Sep 2011
Location: Florida
|
I just picked my 2013 X3 28i from the factory last week (9/24/12) and it came with Silver grills not black!
|
Appreciate
0
|
10-12-2012, 08:12 AM | #14 |
Enlisted Member
10
Rep 40
Posts |
Hi guys
I'm trying to change my black grilles for silver ones. I can get the top and side clips undone but am really struggling with the 3 bottom clips. I just can't see how to reach the tangs with either a screw driver or an allen key. I can't get my hand in from above and I can't reach through the mesh grille lower down. Can anyone help please? |
Appreciate
0
|
10-12-2012, 11:26 AM | #15 |
Enlisted Member
10
Rep 40
Posts |
Panic over - it was the bottom tangs that were difficult to release, but a bit of brute force and determination - and a bruised wrist - sorted it out. Now got my silver grilles in and I'm really pleased with the appearance. I'm off to put ointment on my wrist now!
|
Appreciate
0
|
11-27-2012, 12:56 PM | #17 |
Registered
0
Rep 1
Posts |
How far to bend bumper back?
Hi guys
I tried removing my kidney grill and I was scared of bending it back too much so that it will snap. How far can I bend it back in order for me to get my hand to unclip the bottom clippings? Feedback is appreciated. |
Appreciate
0
|
03-16-2015, 03:45 AM | #18 |
Registered
0
Rep 2
Posts |
Thank you for the great guide! Did it over the weekend and me and my wife loved the result!
Bottom clips a bit difficult to remove but with a bit of the force managed to do it :-) |
Appreciate
0
|
03-18-2015, 07:15 PM | #19 |
IG @bmwF9xG80
3813
Rep 7,593
Posts
Drives: G80 M3, X4M, G07 X7m50
Join Date: Apr 2012
Location: NYC to NJ to Orlando FL
|
Good job but next time use the better brand
__________________
60-130mph 6.5s X4M #HCP
60-130mph 5.0s G80 M3 #OrlandoAutowerks Sauce IG: @bmwF9XG80 |
Appreciate
0
|
04-16-2015, 12:01 PM | #20 |
New Member
0
Rep 12
Posts |
I used black plasti dip to paint just the chrome grill surround and left the inside part the stock silver. The plasti dip has held up for a year and had quite a few car washes.
|
Appreciate
0
|
04-16-2015, 04:00 PM | #21 |
Registered
0
Rep 3
Posts
Drives: 2015 X3 28i Msport (Dinan)
Join Date: Jan 2015
Location: Seattle, WA
|
Thanks for posting. I think this will be the first "upgrade" I perform. I pick up my new 2015 X3 28i Msport (Dinan Stage 1) this weekend. I think the black grilles will look better with the Msport front end than the stock grilles.
|
Appreciate
0
|
04-18-2015, 10:36 PM | #22 |
Lieutenant General
2282
Rep 12,565
Posts
Drives: Z4 M, X5, GX460
Join Date: Apr 2008
Location: CT
iTrader: (99)
Garage List F15 X5 xDrive35i [8.75]
E86 Z4 M [10.00] F10 550i (Retired) [9.17] F25 X3 xDrive35i (R ... [9.43] E82 135is (Retired) [9.50] E85 Z4 M (Retired) [9.41] E90 328i xDrive (Re ... [9.25] E86 Z4 3.0si (Retired) [9.24] |
Thanks OP, just did installed my grills. Fingers are raw from trying to maneuver within that tight space. Took 30 mins tot but 20 was just on the first one trying to figure out how to get the side tabs. Looks great on BSM:
Last edited by 3002 tii; 04-18-2015 at 10:57 PM.. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|