Coding made Easy: A step by step procedure

shawnsheridan · 07-17-2022, 04:23 PM

Quote:

Originally Posted by dom2497

Hello Can you share with me Esys, psdzata and Launcher Pro for my UK LCI M2. Thanks

Your Receive PM function is disabled. PM me when working.

Capnwillyp · 07-22-2022, 05:15 AM

Hi Shawn,
My 2013 F25 was shipped with a CIC HU with the PDC (508A) and Surround View camera system (TRSVC). I recently swapped out the CIC for an NBT Evo HU and everything works as before, exceptÂ…

The PDC sounds work but nothing shows up on the screen when I go into reverse or press the PDC button. I have the TRSVC connected to the proper FBAS1 pins on the Evo HU and the PDC beeps work which leads me to believe that ECU is connected properly. (ISTA and E-Sys both show the TRSVC and PDC ECUs connected. The PDC appears to be integrated with the JBE box.)

Is there some HU coding I need? Is my PDC system Gen1 or Gen2? (It has 4 sensors on the front bumper and 4 sensors on the Rear bumper.)

(Thiis swap did not involve any sort of aftermarket adapter.)

Capnwillyp · 07-22-2022, 08:51 AM

Replying to my own post…

Figured it out!
Coded the Evo as follows:

MACRO_PMA_EINPARKEN to gen1 (was nicht_aktiv)
COMMUNICATION_PARKMASTER to gen1 (was gen2)
CAMERA_SYSTEM to trsvc (was icam_high)

Other relevant settings were OK (PDC_GENERATION = gen1, front and rear sensors set to 4 each, CAM_ECU = werte 01, MACRO_TV_C and MACRO_RV_C both = aktiv).

shawnsheridan · 07-22-2022, 11:04 AM

Quote:

Originally Posted by Capnwillyp

Replying to my own post…

Figured it out!
Coded the Evo as follows:

MACRO_PMA_EINPARKEN to gen1 (was nicht_aktiv)
COMMUNICATION_PARKMASTER to gen1 (was gen2)
CAMERA_SYSTEM to trsvc (was icam_high)

Other relevant settings were OK (PDC_GENERATION = gen1, front and rear sensors set to 4 each, CAM_ECU = werte 01, MACRO_TV_C and MACRO_RV_C both = aktiv).

Cambridge · 07-22-2022, 12:44 PM

Are EST tokens required anymore if using BimmerUtility and E-Sys 3.40?

shawnsheridan · 07-22-2022, 12:46 PM

Quote:

Originally Posted by Cambridge

Are EST tokens required anymore if using BimmerUtility and E-Sys 3.40?

No token needed.

uadissa · 07-23-2022, 12:08 AM

hey guys any chance sending a latest psdzdata lite link ? My i-step has been upgraded by dealer to S15a-22. Quite new. Current version I have ( 4.27.x) goes only upto i-step-15a-20-11

shawnsheridan · 07-23-2022, 01:20 AM

Quote:

Originally Posted by uadissa

hey guys any chance sending a latest psdzdata lite link ? My i-step has been upgraded by dealer to S15a-22. Quite new. Current version I have ( 4.27.x) goes only upto i-step-15a-20-11

PM sent.

DBTinLV · 07-23-2022, 12:49 PM

Hello, newbie here. Followed all instructions (i think) but get error when attempting "SVT Actual - Read (VCM)":

Caused by: java.lang.Exception: ============================================
ECUId:VCM_0x10
job failed with job failed with negative response error:
code: service returned global negative response
description: Service RC_RLE_VCM returned a negative response with response code requestOutOfRange; LinkName: VCM_ETHERNET severity: ERROR

Verified connectivity by pinging the IP of the car from PC.

Any ideas?

Here's my details:
2021 X3, G01
E-sys: 3.40.1
PsdZData_Lite_v4.36.12
Target: S15A_22_07_521_V_004_001_000
(Also tried with the other S15A target, same result.)

shawnsheridan · 07-23-2022, 12:51 PM

Quote:

Originally Posted by DBTinLV

Hello, newbie here. Followed all instructions (i think) but get error when attempting "SVT Actual - Read (VCM)":

Caused by: java.lang.Exception: ============================================
ECUId:VCM_0x10
job failed with job failed with negative response error:
code: service returned global negative response
description: Service RC_RLE_VCM returned a negative response with response code requestOutOfRange; LinkName: VCM_ETHERNET severity: ERROR

Verified connectivity by pinging the IP of the car from PC.

Any ideas?

Here's my details:
2021 X3, G01
E-sys: 3.40.1
PsdZData_Lite_v4.36.12
Target: S15A_22_07_521_V_004_001_000
(Also tried with the other S15A target, same result.)

Use Read (ECU), not Read (VCM).

DBTinLV · 07-23-2022, 01:37 PM

Wow, Bingo! Thanks for super fast response. Now on to the fun part. Will probably be back...

uadissa · 07-23-2022, 06:56 PM

Quote:

Originally Posted by shawnsheridan

Quote:

Originally Posted by uadissa

hey guys any chance sending a latest psdzdata lite link ? My i-step has been upgraded by dealer to S15a-22. Quite new. Current version I have ( 4.27.x) goes only upto i-step-15a-20-11

PM sent.

Thanks for this. Psdzdata was up to date and it had I-step-15a-22-x included. Initially had an error connecting on esys with the new istep, which was fixed by the esysx support guys. Basically using esys 3.3x now instead of 3.27. I have had purchased from them a while back .

When coding, realised that cafd weren't yet trimmed or anything and was able to edit successfully within esys. Out of curiosity do you know from what version it's trimmed?

shawnsheridan · 07-24-2022, 11:27 AM

Quote:

Originally Posted by uadissa

Thanks for this. Psdzdata was up to date and it had I-step-15a-22-x included. Initially had an error connecting on esys with the new istep, which was fixed by the esysx support guys. Basically using esys 3.3x now instead of 3.27. I have had purchased from them a while back .

When coding, realised that cafd weren't yet trimmed or anything and was able to edit successfully within esys. Out of curiosity do you know from what version it's trimmed?

BMW made changes to PSdZData beginning with 54.2 where they removed (aka Trimmed) descriptive text from CAFD (and FAFP) files, making FDL Coding of many ECU's impossible using regular PSdZData files. Yours is trimmed, but mapped by ESysX.

kking22 · 07-26-2022, 12:21 PM

Hello Can you share with me Esys, psdzata and Launcher Pro for my M4 F83 and X4M F98

shawnsheridan · 07-26-2022, 12:58 PM

Quote:

Originally Posted by kking22

Hello Can you share with me Esys, psdzata and Launcher Pro for my M4 F83 and X4M F98

Your Receive PM function is disabled.

And asked and answered on Bimmerfest already:

https://www.bimmerfest.com/threads/c.../post-13720703

Glock20C · 08-01-2022, 03:48 PM

Hi Shawn,

Newbie here. I have a 2013 F25 (5/12 production) and swapped out the CIC to a NBT EVO. Everything works after changing the ZGW Mid to ZGW-4SK. Missing function such as gyro information, no memory for XM radio stations, speaker/amplifier makes this ticking sound. However, my biggest problem I cannot get the car smogged (emissions tested). Have you had any experience with these issues and would coding help remedy this?

I have not posted enough so my PM function is still disabled.

Any thoughts/assistance is appreciated.

Thank you!

shawnsheridan · 08-01-2022, 05:34 PM

Quote:

Originally Posted by Glock20C

Hi Shawn,

Newbie here. I have a 2013 F25 (5/12 production) and swapped out the CIC to a NBT EVO. Everything works after changing the ZGW Mid to ZGW-4SK. Missing function such as gyro information, no memory for XM radio stations, speaker/amplifier makes this ticking sound. However, my biggest problem I cannot get the car smogged (emissions tested). Have you had any experience with these issues and would coding help remedy this?

I have not posted enough so my PM function is still disabled.

Any thoughts/assistance is appreciated.

Thank you!

No, sorry, no experience at all.

fullmoonguru · 08-03-2022, 03:48 PM

Newby here. I am about to replace our EDC struts with Koni's I need to know what to unplug and how to code out the EDC. I have the cable & have installed E-sys & Bimmer Utility.

I would appreciate anyone who could point me in the right direction.

shawnsheridan · 08-03-2022, 09:41 PM

Quote:

Originally Posted by fullmoonguru

Newby here. I am about to replace our EDC struts with Koni's I need to know what to unplug and how to code out the EDC. I have the cable & have installed E-sys & Bimmer Utility.

I would appreciate anyone who could point me in the right direction.

Nothing Iv'e done, but I think to code out EDC:

Edit FA and remove 2VA, 229, and 223, and use modified FA to Code DSC, HU_CIC / HU_NBT, KOMBI, and ICM.

mightyi6 · 08-04-2022, 09:04 AM

Hello Shawn,

could you help with the token for E-sys FDL coding? Thank you!

shawnsheridan · 08-04-2022, 09:29 AM

Quote:

Originally Posted by mightyi6

Hello Shawn,

could you help with the token for E-sys FDL coding? Thank you!

PM sent.

fullmoonguru · 08-04-2022, 09:35 AM

Newby here. I'm having trouble getting a connection through E-Sys. Are the directions at the beginning of this thread correct for using E-Sys 3.38+ w/BimmerUtility?

My laptop says it's connected to unknown network with no internet. Then I open E-Sys and click the connect button and get this error:

Connection check failed.
Gateway/ECUs are not correctly connected or not responding.
However Functions using the ODX-Data can be used. [G188]

07-22-2022, 05:15 AM	#3522
Capnwillyp Registered 0 Rep 2 Posts Drives: 2013 BMW X3 Join Date: May 2022 Location: Florida iTrader: (0) Garage List 2013 BMW X3 [0.00]	Hi Shawn, My 2013 F25 was shipped with a CIC HU with the PDC (508A) and Surround View camera system (TRSVC). I recently swapped out the CIC for an NBT Evo HU and everything works as before, exceptÂ… The PDC sounds work but nothing shows up on the screen when I go into reverse or press the PDC button. I have the TRSVC connected to the proper FBAS1 pins on the Evo HU and the PDC beeps work which leads me to believe that ECU is connected properly. (ISTA and E-Sys both show the TRSVC and PDC ECUs connected. The PDC appears to be integrated with the JBE box.) Is there some HU coding I need? Is my PDC system Gen1 or Gen2? (It has 4 sensors on the front bumper and 4 sensors on the Rear bumper.) (Thiis swap did not involve any sort of aftermarket adapter.)
	Appreciate 0 Quote

07-22-2022, 08:51 AM	#3523
Capnwillyp Registered 0 Rep 2 Posts Drives: 2013 BMW X3 Join Date: May 2022 Location: Florida iTrader: (0) Garage List 2013 BMW X3 [0.00]	Replying to my own post… Figured it out! Coded the Evo as follows: MACRO_PMA_EINPARKEN to gen1 (was nicht_aktiv) COMMUNICATION_PARKMASTER to gen1 (was gen2) CAMERA_SYSTEM to trsvc (was icam_high) Other relevant settings were OK (PDC_GENERATION = gen1, front and rear sensors set to 4 each, CAM_ECU = werte 01, MACRO_TV_C and MACRO_RV_C both = aktiv).
	Appreciate 0 Quote

07-22-2022, 12:44 PM	#3525
Cambridge New Member 0 Rep 6 Posts Drives: 2017 BMW X3 Join Date: Jul 2022 Location: NY iTrader: (0)	Are EST tokens required anymore if using BimmerUtility and E-Sys 3.40?
	Appreciate 0 Quote

07-23-2022, 12:08 AM	#3527
uadissa Enlisted Member 9 Rep 41 Posts Drives: X3 G01 20D M-Sport Join Date: Jan 2018 Location: Melbourne iTrader: (0)	hey guys any chance sending a latest psdzdata lite link ? My i-step has been upgraded by dealer to S15a-22. Quite new. Current version I have ( 4.27.x) goes only upto i-step-15a-20-11
	Appreciate 0 Quote

07-23-2022, 12:49 PM	#3529
DBTinLV Registered 0 Rep 2 Posts Drives: 2021 BMW X3 xDrive30i Join Date: Jul 2022 Location: USA iTrader: (0)	Hello, newbie here. Followed all instructions (i think) but get error when attempting "SVT Actual - Read (VCM)": Caused by: java.lang.Exception: ============================================ ECUId:VCM_0x10 job failed with job failed with negative response error: code: service returned global negative response description: Service RC_RLE_VCM returned a negative response with response code requestOutOfRange; LinkName: VCM_ETHERNET severity: ERROR Verified connectivity by pinging the IP of the car from PC. Any ideas? Here's my details: 2021 X3, G01 E-sys: 3.40.1 PsdZData_Lite_v4.36.12 Target: S15A_22_07_521_V_004_001_000 (Also tried with the other S15A target, same result.)
	Appreciate 0 Quote

07-23-2022, 01:37 PM	#3531
DBTinLV Registered 0 Rep 2 Posts Drives: 2021 BMW X3 xDrive30i Join Date: Jul 2022 Location: USA iTrader: (0)	Wow, Bingo! Thanks for super fast response. Now on to the fun part. Will probably be back...
	Appreciate 0 Quote

07-26-2022, 12:21 PM	#3534
kking22 Registered 0 Rep 1 Posts Drives: BMW M4 F83 & BMW X4M F98 Join Date: Jul 2022 Location: Switzerland iTrader: (0)	Hello Can you share with me Esys, psdzata and Launcher Pro for my M4 F83 and X4M F98
	Appreciate 0 Quote

08-01-2022, 03:48 PM	#3536
Glock20C New Member 2 Rep 6 Posts Drives: BMW X3 F25 Join Date: Jun 2022 Location: California iTrader: (0)	Hi Shawn, Newbie here. I have a 2013 F25 (5/12 production) and swapped out the CIC to a NBT EVO. Everything works after changing the ZGW Mid to ZGW-4SK. Missing function such as gyro information, no memory for XM radio stations, speaker/amplifier makes this ticking sound. However, my biggest problem I cannot get the car smogged (emissions tested). Have you had any experience with these issues and would coding help remedy this? I have not posted enough so my PM function is still disabled. Any thoughts/assistance is appreciated. Thank you!
	Appreciate 0 Quote

08-03-2022, 03:48 PM	#3538
fullmoonguru New Member 0 Rep 11 Posts Drives: 2014 X3 Join Date: Aug 2022 Location: NC iTrader: (0)	Newby here. I am about to replace our EDC struts with Koni's I need to know what to unplug and how to code out the EDC. I have the cable & have installed E-sys & Bimmer Utility. I would appreciate anyone who could point me in the right direction.
	Appreciate 0 Quote

08-04-2022, 09:04 AM	#3540
mightyi6 Registered 0 Rep 3 Posts Drives: F31 328xi; E90 328xi; 2017 i3 Join Date: Aug 2013 Location: Massachusetts iTrader: (0)	Hello Shawn, could you help with the token for E-sys FDL coding? Thank you!
	Appreciate 0 Quote

08-04-2022, 09:35 AM	#3542
fullmoonguru New Member 0 Rep 11 Posts Drives: 2014 X3 Join Date: Aug 2022 Location: NC iTrader: (0)	Newby here. I'm having trouble getting a connection through E-Sys. Are the directions at the beginning of this thread correct for using E-Sys 3.38+ w/BimmerUtility? My laptop says it's connected to unknown network with no internet. Then I open E-Sys and click the connect button and get this error: Connection check failed. Gateway/ECUs are not correctly connected or not responding. However Functions using the ODX-Data can be used. [G188]
	Appreciate 0 Quote