BMW X3 Forum
BMW X3 Forum
Welcome to the ultimate BMW X3 community.
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
Post Reply
 
Thread Tools Search this Thread
      05-02-2012, 08:52 PM   #1
stactum
Private
11
Rep
73
Posts

Drives: 340i xDrive M-Sport
Join Date: Mar 2012
Location: Sussex, WI USA

iTrader: (0)

How to remove kidney grille on F25 for painting

Hi guys,

So after about two weeks with my 2013 X3 I wasn't fully satisfied with black grille they changed for 2013 figured that to buy 2 would cost me about $210 (in US) so I decided to paint it. There are few good guides on how to remove kidney grille, but none for X3 F25 so while I used other guides to remove it I decided to create one.

This is what it looks in black:


Some other guides:
X1 Guide
X3 short overview
Another informative guide

Tools I used:
Angle tool
Multiple small screwdrivers
Torx T30

Paint:
Rust-oleum Universal Metallic Dark Steel (picked from 4 different colors)

Note: I don't have jetwashers so in case you do, please refer to a guide above for X1, but explains what to do with jetwashers.

1. Start by removing rubber that covers screw heads - you just pull it towards the engine and it comes out. It's not glued or anything.
Then use T30 torx to remove 6 screws from the top of the bumper.




2. To remove the grille you have carefully pull the bumper towards you and use long screwdriver to unlock the clips that holding grille. I did it in the order shown on the picture. After you unlocked 1-5 use right angle tool to unlock 6-8. It can be somewhat tricky and it's the hardest part of the whole process, but it took me about 10 minutes to remove both grilles.



3. After you popped them out it's time to take black inserts from the frame. There are few steps I took in order to do that.


Since there are quite a few locks it's been very heplful for me to use small screwdrivers and some tools to keep them unlocked.



After I did that it was easy to unlock it from the bottom and remove black inserts.



4. I tried multiple paints on some ground anchors just to see which one will look better on the grille.



I picked Rust Oleum Universal Metallic Dark Steel



And painted both grilles. I added probably 5 layers or so. I figured, it's easier to add multiple thin layers than one thick. Also, have some Goo Gone and paper towel handy in case you have some places with thicker paint. Just softly remove it from the grille, make sure not to rub too hard, otherwise you'll see imperfections later.



I let it dry for a few hours and after I could touch it I got inserts in the frame (easy, just pop them inside) and insert grilles inside the bumper (just like you saw in Megafactories).

So here are some final results:







Thanks for reading, I hope it was helpful!

Last edited by stactum; 05-02-2012 at 10:22 PM..
Appreciate 0
      05-02-2012, 09:59 PM   #2
swallowtail
Private
Australia
7
Rep
86
Posts

Drives: 2018 M2 Competition DCT
Join Date: Nov 2011
Location: Brisbane, Australia

iTrader: (0)

Very cool, looks sweet. I much prefer that look over the black.

Just one thing to note - I hate imageshack, it has popups (I just got one to "f***sexygirls.com" or something similar.
Appreciate 0
      05-03-2012, 07:12 AM   #3
n55x3
Captain
72
Rep
876
Posts

Drives: n55 BMWs
Join Date: Dec 2011
Location: us - ohio

iTrader: (0)

Man, those look great, thanks for sharing!!

I didn't realize the 2013 models got black grills. Funny. Ours look almost exactly like yours after painting. I have been wanting to switch ours over to black. Haven't gotten around to it yet.

We could have just traded!! ;-)
Appreciate 0
      05-03-2012, 08:18 AM   #4
swallowtail
Private
Australia
7
Rep
86
Posts

Drives: 2018 M2 Competition DCT
Join Date: Nov 2011
Location: Brisbane, Australia

iTrader: (0)

Quote:
Originally Posted by n55x3
Man, those look great, thanks for sharing!!

I didn't realize the 2013 models got black grills. Funny. Ours look almost exactly like yours after painting. I have been wanting to switch ours over to black. Haven't gotten around to it yet.

We could have just traded!! ;-)
4 cyl get black grilles, 6 cyl get the silver. With the 28i move from 6 to a T4 the grille is now black...
__________________
Current drive: 2018 M2 Competition DCT, Sunset Orange
Previous: BMW X3 xDrive 30d
Appreciate 0
      05-03-2012, 08:05 PM   #5
sbt007
Major
sbt007's Avatar
United_States
619
Rep
1,089
Posts

Drives: 2021 X3 M40i
Join Date: Feb 2012
Location: CA

iTrader: (0)

Garage List
2021 BMW X3 M40i  [10.00]
That is an amazing job. I prefer the silver/titanium as well.
That being said, many people actually pay to make it black, so it would be nice if dealerships facilitated an exchange.
Appreciate 0
      05-03-2012, 09:10 PM   #6
kskpsu
First Lieutenant
kskpsu's Avatar
United_States
176
Rep
360
Posts

Drives: 1M; E90 M3 ZCP; M4 GTS
Join Date: Jul 2011
Location: Minneapolis, MN

iTrader: (0)

Garage List
'11 BMW 1M  [9.83]
Quote:
Originally Posted by sbt007 View Post
That is an amazing job. I prefer the silver/titanium as well.
That being said, many people actually pay to make it black, so it would be nice if dealerships facilitated an exchange.
Sad, but true. Paid to go with "BMW Performance" grilles on my 1M...i.e. all black. Would probably trade my titanium grilles on the X3 for the new 4 cylinder setup..I waffle back and forth on that one.
__________________
-kskpsu
Appreciate 0
      08-09-2012, 10:53 AM   #7
empirevalley
New Member
2
Rep
19
Posts

Drives: 2012 X3 xDrive28i
Join Date: Aug 2009
Location: Colorado

iTrader: (0)

Quote:
Originally Posted by stactum View Post
Hi guys,

So after about two weeks with my 2013 X3 I wasn't fully satisfied with black grille they changed for 2013 figured that to buy 2 would cost me about $210 (in US) so I decided to paint it. There are few good guides on how to remove kidney grille, but none for X3 F25 so while I used other guides to remove it I decided to create one.

This is what it looks in black:


Some other guides:
X1 Guide
X3 short overview
Another informative guide

Tools I used:
Angle tool
Multiple small screwdrivers
Torx T30

Paint:
Rust-oleum Universal Metallic Dark Steel (picked from 4 different colors)

Note: I don't have jetwashers so in case you do, please refer to a guide above for X1, but explains what to do with jetwashers.

1. Start by removing rubber that covers screw heads - you just pull it towards the engine and it comes out. It's not glued or anything.
Then use T30 torx to remove 6 screws from the top of the bumper.




2. To remove the grille you have carefully pull the bumper towards you and use long screwdriver to unlock the clips that holding grille. I did it in the order shown on the picture. After you unlocked 1-5 use right angle tool to unlock 6-8. It can be somewhat tricky and it's the hardest part of the whole process, but it took me about 10 minutes to remove both grilles.



3. After you popped them out it's time to take black inserts from the frame. There are few steps I took in order to do that.


Since there are quite a few locks it's been very heplful for me to use small screwdrivers and some tools to keep them unlocked.



After I did that it was easy to unlock it from the bottom and remove black inserts.



4. I tried multiple paints on some ground anchors just to see which one will look better on the grille.



I picked Rust Oleum Universal Metallic Dark Steel



And painted both grilles. I added probably 5 layers or so. I figured, it's easier to add multiple thin layers than one thick. Also, have some Goo Gone and paper towel handy in case you have some places with thicker paint. Just softly remove it from the grille, make sure not to rub too hard, otherwise you'll see imperfections later.



I let it dry for a few hours and after I could touch it I got inserts in the frame (easy, just pop them inside) and insert grilles inside the bumper (just like you saw in Megafactories).

So here are some final results:







Thanks for reading, I hope it was helpful!
Thanks for the photos and instructions. I ordered a set of black grilles for my 2012 X328i from getbmwparts.com for $52 each plus shipping and handling. I removed the OEM chrome grilles and replaced them with the black grilles this morning - took a total of 15 minutes. Some more installation advice: I used a right angle tool - I bought a set from Harbor Freight for a couple of bucks - which is absolutely necessary to depress the latches on the bottom of the grilles for removal.
Appreciate 0
      10-01-2012, 11:20 AM   #8
Chris111
Enlisted Member
United Kingdom
10
Rep
40
Posts

Drives: BMW X5 40i Msport
Join Date: Aug 2012
Location: Surrey, UK

iTrader: (0)

Hey guys, what is the angle tool you used? any chance you could post a photo of it please?
Appreciate 0
      10-01-2012, 11:31 AM   #9
carlili4190
Second Lieutenant
20
Rep
201
Posts

Drives: 07 Nissan 350Z, 11 BMW X3
Join Date: Mar 2011
Location: Lincoln Park

iTrader: (0)

Quote:
Originally Posted by Chris111 View Post
Hey guys, what is the angle tool you used? any chance you could post a photo of it please?
I never ended up using an"angle tool" because I had no idea what it was! I used a flat head screw driver and positioned my hand so I could unhook all the tabs.
Appreciate 0
      10-01-2012, 11:55 AM   #10
Chris111
Enlisted Member
United Kingdom
10
Rep
40
Posts

Drives: BMW X5 40i Msport
Join Date: Aug 2012
Location: Surrey, UK

iTrader: (0)

Ok thanks!
Appreciate 0
      10-01-2012, 01:08 PM   #11
MattUK
Captain Unsensible
MattUK's Avatar
United Kingdom
99
Rep
737
Posts

Drives: 2016 M240i Coupe - Estoril
Join Date: Sep 2011
Location: United Kingdom

iTrader: (0)

Garage List
2016 BMW M240i  [0.00]
I used an allen key that had a right angle to get the 2 I couldn't get to with my finger
Appreciate 0
      10-02-2012, 03:43 AM   #12
slyfox
Private First Class
slyfox's Avatar
Belgium
4
Rep
106
Posts

Drives: X3-20d (2013)
Join Date: Sep 2012
Location: Limburg (B)

iTrader: (0)

Empirevalley.

Wow thanks for the heads up on the grill painting. looks realllly good.
Well done.
Appreciate 0
      10-02-2012, 09:56 AM   #13
pacecapt
Private
9
Rep
85
Posts

Drives: 2022 X3 M40i
Join Date: Sep 2011
Location: Florida

iTrader: (0)

Garage List
2014 BMW 435i  [0.00]
2013 BMW X3 28i  [0.00]
I just picked my 2013 X3 28i from the factory last week (9/24/12) and it came with Silver grills not black!
Appreciate 0
      10-12-2012, 08:12 AM   #14
Chris111
Enlisted Member
United Kingdom
10
Rep
40
Posts

Drives: BMW X5 40i Msport
Join Date: Aug 2012
Location: Surrey, UK

iTrader: (0)

Hi guys
I'm trying to change my black grilles for silver ones. I can get the top and side clips undone but am really struggling with the 3 bottom clips. I just can't see how to reach the tangs with either a screw driver or an allen key. I can't get my hand in from above and I can't reach through the mesh grille lower down. Can anyone help please?
Appreciate 0
      10-12-2012, 11:26 AM   #15
Chris111
Enlisted Member
United Kingdom
10
Rep
40
Posts

Drives: BMW X5 40i Msport
Join Date: Aug 2012
Location: Surrey, UK

iTrader: (0)

Panic over - it was the bottom tangs that were difficult to release, but a bit of brute force and determination - and a bruised wrist - sorted it out. Now got my silver grilles in and I'm really pleased with the appearance. I'm off to put ointment on my wrist now!
Appreciate 0
      10-22-2012, 10:28 AM   #16
dandanio
The one that drives!
dandanio's Avatar
United_States
22
Rep
187
Posts

Drives: 11 x3 35i/09 Jetta TDI
Join Date: Mar 2009
Location: New England

iTrader: (0)

Excellent removal guide!
Appreciate 0
      11-27-2012, 12:56 PM   #17
MHauman
Registered
0
Rep
1
Posts

Drives: x3 M 2.0d
Join Date: Nov 2012
Location: South Africa

iTrader: (0)

How far to bend bumper back?

Hi guys

I tried removing my kidney grill and I was scared of bending it back too much so that it will snap.

How far can I bend it back in order for me to get my hand to unclip the bottom clippings?

Feedback is appreciated.
Appreciate 0
      03-16-2015, 03:45 AM   #18
Golum
Registered
Switzerland
0
Rep
2
Posts

Drives: X3 2.0d
Join Date: Feb 2015
Location: Lausanne

iTrader: (0)

Thank you for the great guide! Did it over the weekend and me and my wife loved the result!
Bottom clips a bit difficult to remove but with a bit of the force managed to do it :-)
Appreciate 0
      03-18-2015, 07:15 PM   #19
FSociety
IG @bmwF9xG80
FSociety's Avatar
3810
Rep
7,593
Posts

Drives: G80 M3, X4M, G07 X7m50
Join Date: Apr 2012
Location: NYC to NJ to Orlando FL

iTrader: (3)

Garage List
2023 BMW G80 M3  [0.00]
2020 BMW X4MC  [0.00]
16' BMW X4 M40i  [10.00]
06 Cadillac STS  [0.00]
Good job but next time use the better brand

__________________
60-130mph 6.5s X4M #HCP
60-130mph 5.0s G80 M3 #OrlandoAutowerks Sauce

IG: @bmwF9XG80

Appreciate 0
      04-16-2015, 12:01 PM   #20
BFox
New Member
0
Rep
12
Posts

Drives: 2013 X3 35i M Sport
Join Date: May 2014
Location: United States

iTrader: (0)

I used black plasti dip to paint just the chrome grill surround and left the inside part the stock silver. The plasti dip has held up for a year and had quite a few car washes.
Attached Images
 
Appreciate 0
      04-16-2015, 04:00 PM   #21
Northwest_Bob
Registered
0
Rep
3
Posts

Drives: 2015 X3 28i Msport (Dinan)
Join Date: Jan 2015
Location: Seattle, WA

iTrader: (0)

Garage List
2015 BMW X3 28i  [0.00]
Thanks for posting. I think this will be the first "upgrade" I perform. I pick up my new 2015 X3 28i Msport (Dinan Stage 1) this weekend. I think the black grilles will look better with the Msport front end than the stock grilles.
Appreciate 0
      04-18-2015, 10:36 PM   #22
3002 tii
Lieutenant General
3002 tii's Avatar
2272
Rep
12,559
Posts

Drives: Z4 M, X5, GX460
Join Date: Apr 2008
Location: CT

iTrader: (99)

Garage List
Thanks OP, just did installed my grills. Fingers are raw from trying to maneuver within that tight space. Took 30 mins tot but 20 was just on the first one trying to figure out how to get the side tabs. Looks great on BSM:

__________________
Follow for latest mods

Last edited by 3002 tii; 04-18-2015 at 10:57 PM..
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 10:14 AM.




xbimmers
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST