[RolaNoCalhau]

Originally Posted by shawnsheridan

When you hit the Connect Button, you were presented a window with a list of Targets, and you selected one. This target had a name, something like F025-14-11-502.

FF is not available from the Dropdown list of predefined settings. You need to change the Werte Value directly:

E-Sys - How to Change Werte Values.pdf:

http://f30.bimmerpost.com/forums/att...3&d=1338274757

Digital speed appears in the BC Cluster, and you must cycle through the settings with the BC Stalk to display it.

Tks Shawn, I'll try that again and give you the info later.

In the meanwhile, can you advise on how to remove the seatbelt warning?
I couldn't find the 3001 section in ACSM module...

[shawnsheridan]

Originally Posted by RolaNoCalhau

Tks Shawn, I'll try that again and give you the info later.

In the meanwhile, can you advise on how to remove the seatbelt warning?
I couldn't find the 3001 section in ACSM module...

Do not restrict your search to just a section like 3001. These vary by CAFD version. Use the search bar at the top, and search for FDL Codes by name. Understand though that the search bar searches only from the Top => Down, so make sure you start at the top of the CAFD, and do not have any leading or trailing spaces in your search term.

[RolaNoCalhau]

Originally Posted by shawnsheridan

FF is not available from the Dropdown list of predefined settings. You need to change the Werte Value directly:

Shawn, regarding this issue I read and understood how to change werte value. Tks
However, still don't know which option to choose under Ausgelesen (1st parameter), because it only has "nicht_aktiv", "8_kmh" and "3_kmh" whereas the cheat chart only refers "value = FF" in the "new value" column.

[shawnsheridan]

Originally Posted by RolaNoCalhau

Shawn, regarding this issue I read and understood how to change werte value. Tks
However, still don't know which option to choose under Ausgelesen (1st parameter), because it only has "nicht_aktiv", "8_kmh" and "3_kmh" whereas the cheat chart only refers "value = FF" in the "new value" column.

You change only the Werte Value. Leave the Drop-down alone. It will change to Unknown after you write custom Werte Value to ECU.

[RolaNoCalhau]

Originally Posted by shawnsheridan

You change only the Werte Value. Leave the Drop-down alone. It will change to Unknown after you write custom Werte Value to ECU.

Great! Tks. I'll post results.

[RolaNoCalhau]

Hi again Shawn!

Originally Posted by shawnsheridan

What is the Connection Target Name? It contains the I-Step (PSdZData) version.

Originally Posted by shawnsheridan

When you hit the Connect Button, you were presented a window with a list of Targets, and you selected one. This target had a name, something like F025-14-11-502.

Please see the attached print screen.

Originally Posted by shawnsheridan

Digital speed appears in the BC Cluster, and you must cycle through the settings with the BC Stalk to display it.

It worked and I found it, tks.

Originally Posted by shawnsheridan

Do not restrict your search to just a section like 3001. These vary by CAFD version. Use the search bar at the top, and search for FDL Codes by name. Understand though that the search bar searches only from the Top => Down, so make sure you start at the top of the CAFD, and do not have any leading or trailing spaces in your search term.

This one didn't work. I searched thoroughly the entire CAFD and it isn't there.
However I found strange that inside the ACSM module there are 3 CFD files with green check marks. But when I "read coding data" only one file turns into a folder, the other 2 have errors.

Report:
ACSM [1] [DY00991]
readCPS o.k.
CAFD_00000909_004_003_007 Fehler:
File for "cafd_00000909-004_003_007" not found! [C012]

ACSM [1] [DY00991]
readCPS o.k.
CAFD_0000090A_004_003_049 Fehler:
File for "cafd_0000090a-004_003_049" not found! [C012]

ACSM [1] [DY00991]
readCPS o.k.
CAFD_0000090B_004_004_012.ncd generated

Is it possible that the wanted function (remove the seatbelt warning) could be inside of either one of those 2?

[RolaNoCalhau]

Is it possible to change CAFD values offline and then connect and start in the step 19? If so, do I still need to read (VCM) in SVT Actual?

[shawnsheridan]

Originally Posted by RolaNoCalhau

Hi again Shawn!

Please see the attached print screen.

It worked and I found it, tks.

This one didn't work. I searched thoroughly the entire CAFD and it isn't there.
However I found strange that inside the ACSM module there are 3 CFD files with green check marks. But when I "read coding data" only one file turns into a folder, the other 2 have errors.

Report:
ACSM [1] [DY00991]
readCPS o.k.
CAFD_00000909_004_003_007 Fehler:
File for "cafd_00000909-004_003_007" not found! [C012]

ACSM [1] [DY00991]
readCPS o.k.
CAFD_0000090A_004_003_049 Fehler:
File for "cafd_0000090a-004_003_049" not found! [C012]

ACSM [1] [DY00991]
readCPS o.k.
CAFD_0000090B_004_004_012.ncd generated

Is it possible that the wanted function (remove the seatbelt warning) could
be inside of either one of those 2?

It is in the 1st (Top) CAFD, so that explains that.

Download and copy to your CAFD library folder (C:\Data\psdzdata\swe\cafd):

cafd_00000909.caf.004_003_007:

https://mega.co.nz/#!A5pwURyZ!K65IVQ...wEOx1z4xPot_j0

Originally Posted by RolaNoCalhau

Is it possible to change CAFD values offline and then connect and start in the step 19? If so, do I still need to read (VCM) in SVT Actual?

Yes. You can read ECU, disconnect from car, make changes offline, connect back to car, and write changes to car via Code FDL. You will need to Activate FA and read SVT again.

[RolaNoCalhau]

Originally Posted by shawnsheridan

It is in the 1st (Top) CAFD, so that explains that.

Download and copy to your CAFD library folder (C:\Data\psdzdata\swe\cafd):

cafd_00000909.caf.004_003_007:

https://mega.co.nz/#!A5pwURyZ!K65IVQ...wEOx1z4xPot_j0


Yes. You can read ECU, disconnect from car, make changes offline, connect back to car, and write changes to car via Code FDL. You will need to Activate FA and read SVT again.

Tks Shawn, download it already and will give it a try.

Another question: so that file I just downloaded was missing from psdzdata archive. Since I have 6 other CFD files with green check marks that don't turn into a folder, I might be missing those as well.
Can you check error report attached and if so send those files?

For example the CAS module has 1 with green check mark and it won't generate .ncd as well.

Tks

[shawnsheridan]

Originally Posted by RolaNoCalhau

Tks Shawn, download it already and will give it a try.

Another question: so that file I just downloaded was missing from psdzdata archive. Since I have 6 other CFD files with green check marks that don't turn into a folder, I might be missing those as well.
Can you check error report attached and if so send those files?

For example the CAS module has 1 with green check mark and it won't generate .ncd as well.

Tks

Best I can tell it is as follows:

File for "cafd_00000909-004_003_007" not found! [C012] Provided Above
File for "cafd_0000090a-004_003_049" not found! [C012] Not Needed - Nothing to code in this CAFD

These were added new in 55.0, and there is no working version of these CAFD files:

File for "cafd_0000000f-005_025_044" not found! [C012]
File for "cafd_00000c18-014_082_005" not found! [C012]
File for "cafd_0000029b-000_009_006" not found! [C012]
File for "cafd_00000014-004_100_001" not found! [C012]
File for "cafd_00000018-004_010_006" not found! [C012]

[RolaNoCalhau]

Originally Posted by shawnsheridan

Best I can tell it is as follows:

File for "cafd_00000909-004_003_007" not found! [C012] Provided Above
File for "cafd_0000090a-004_003_049" not found! [C012] Not Needed - Nothing to code in this CAFD

These were added new in 55.0, and there is no working version of these CAFD files:

File for "cafd_0000000f-005_025_044" not found! [C012]
File for "cafd_00000c18-014_082_005" not found! [C012]
File for "cafd_0000029b-000_009_006" not found! [C012]
File for "cafd_00000014-004_100_001" not found! [C012]
File for "cafd_00000018-004_010_006" not found! [C012]

Tks Shawn!

But, in that case, why am I not being able to access CAS module?
There is plenty to code therein...

[shawnsheridan]

Originally Posted by RolaNoCalhau

Tks Shawn!

But, in that case, why am I not being able to access CAS module?
There is plenty to code therein...

I wrote you above why.

cafd_0000000f-005_025_044 was added new in 55.0, and there is no working version of these CAFD files.

[RolaNoCalhau]

Originally Posted by shawnsheridan

I wrote you above why.

cafd_0000000f-005_025_044 was added new in 55.0, and there is no working version of these CAFD files.

Ok! Sorry for being insistent but I still have some difficulties in understanding all this.

But thank you very much, I wouldn't have been successful without your help. Tks for being there!

[shawnsheridan]

Originally Posted by RolaNoCalhau

Ok! Sorry for being insistent but I still have some difficulties in understanding all this.

But thank you very much, I wouldn't have been successful without your help. Tks for being there!

BMW made changes to PSdZData beginning with 54.2 and expanded upon them in 54.3, and expanded upon further in 55.0 / 55.1 where they removed descriptive text from CAFD (and FAFP) files, making FDL Coding of many ECU's impossible using regular PSdZData files.

[RolaNoCalhau]

Originally Posted by shawnsheridan

BMW made changes to PSdZData beginning with 54.2 and expanded upon them in 54.3, and expanded upon further in 55.0 / 55.1 where they removed descriptive text from CAFD (and FAFP) files, making FDL Coding of many ECU's impossible using regular PSdZData files.

Tks for the explanation. But if you mention "regular PSdZData files", can that mean that other type of files may exist now or in the near future that can be used for the same purpose?

[RolaNoCalhau]

Shawn, remembered another one: I read somewhere in this thread that it’s possible to code the function “move the car with the door open”, but I can’t find it in the cheat chart.
Do you know where is this?

[X3Bimmer]

Originally Posted by shawnsheridan

BMW made changes to PSdZData beginning with 54.2 and expanded upon them in 54.3, and expanded upon further in 55.0 / 55.1 where they removed descriptive text from CAFD (and FAFP) files, making FDL Coding of many ECU's impossible using regular PSdZData files.

So, if I reading this correctly the next time I get the X3 serviced, I won't be able to code anything if the software is updated... True?

[shawnsheridan]

Originally Posted by RolaNoCalhau

Tks for the explanation. But if you mention "regular PSdZData files", can that mean that other type of files may exist now or in the near future that can be used for the same purpose?

Regular being the normal source for PSdZData, which is ISTA/P. It is conceivable though that BMW has a master set of Untrimmed PSdZData, so I leave open the possibility that FDL Coding is still possible, but even assuming they do, having that copy leaked out would be unlikely.

[shawnsheridan]

Originally Posted by RolaNoCalhau

Shawn, remembered another one: I read somewhere in this thread that it’s possible to code the function “move the car with the door open”, but I can’t find it in the cheat chart.
Do you know where is this?

I am not aware of such code. I think it may be possible to Reverse with door open so long as Seatbelt is on and CAS = ER_KEYOUT_AUTOVR = aktiv is coded.

[shawnsheridan]

Originally Posted by X3Bimmer

So, if I reading this correctly the next time I get the X3 serviced, I won't be able to code anything if the software is updated... True?

Yes, that is correct, at least not FDL Code anything. VO Coding is still possible.

[RolaNoCalhau]

Originally Posted by shawnsheridan

Yes, that is correct, at least not FDL Code anything. VO Coding is still possible.

What is VO coding?

[shawnsheridan]

Originally Posted by RolaNoCalhau

What is VO coding?

For VO Coding you select the ECU itself, not the CAFD File.

VO = Vehicle Order

VO Code = Coding of all FDL's (100% of the ECU) to predetermined settings based on the Vehicle Order.

Connect => Read FA (VO) => Activate FA (VO) => Read SVT (VCM) => Right-Click on ECU (the ECU itself not the underlying CAFD) => Select CODE.

FDL = Function Data Line

FDL Code = Coding of individual FDL's in an ECU, overriding the VO Coding.

Connect => Read FA (VO) => Activate FA (VO) => Read SVT (VCM) => Right-Click on the ECU CAFD and select Read Coding Data => Expand the CAFD Folder by clicking + symbol => Right-Click on the CAFD file and select Edit => Edit CAFD as desired => Click the Blue Floppy Disc Icon to Save CAFD => Click the green back arrow icon => Right-Click on the CAFD file => Select FDL CODE.