[shawnsheridan]

Originally Posted by TonyX3driver

Shawn, I've lack of space on my old notebook with E-Sys.
Can I copy and use in my case only the folder " C:\Data\psdzdata\mainseries\F025\xxxxxxxxx" from 54.1_PsdZData_Full??

No. The firmware files ares in ...\psdzdata\swe\swfl so just copying files from ...\psdzdata\mainseries\F025\xxxxxxxxx gets you nothing.

Your flashing an ECU here, which is risky to begin with. You do not want to be using partial psdzdata anyway.

If you are out of space on your local hard drive, you should leave local psdzdata folder empty and put psdzdata folder extracted from PSdZData Full archive on an external drive, and then use Windows MKLINK command to create a Windows Symbolic Link, for example from C:\ESysData\psdzdata to E:\psdzdata.

You can use one of these MKLINK GUI utilities to simply creation of the Symbolic Link:

http://sourceforge.net/projects/symlink-creator/

http://sourceforge.net/projects/windowssymbolic/

[TonyX3driver]

Originally Posted by shawnsheridan

No. The firmware files ares in ...\psdzdata\swe\swfl so just copying files from ...\psdzdata\mainseries\F025\xxxxxxxxx gets you nothing.

Your flashing an ECU here, which is risky to begin with. You do not want to be using partial psdzdata anyway.

If you are out of space on your local hard drive, you should leave local psdzdata folder empty and put psdzdata folder extracted from PSdZData Full archive on an external drive, and then use Windows MKLINK command to create a Windows Symbolic Link, for example from C:\ESysData\psdzdata to E:\psdzdata.

You can use one of these MKLINK GUI utilities to simply creation of the Symbolic Link:

http://sourceforge.net/projects/symlink-creator/

http://sourceforge.net/projects/windowssymbolic/

Shawn, problem....

[TonyX3driver]

Originally Posted by TonyX3driver

Shawn, problem....

all is death now....

engine running, but Kombi is dark
only left turn indicator is flashing.
Is there any way how to tunr back? Battery off for 30min or so??

[shawnsheridan]

Originally Posted by TonyX3driver

all is death now....

engine running, but Kombi is dark
only left turn indicator is flashing.
Is there any way how to tunr back? Battery off for 30min or so??

No, I think only recovery will come form a successful flash. So, I would try and flash it again.

Was motor running when you originally flashed it?

[TonyX3driver]

Originally Posted by shawnsheridan

No, I think only recovery will come form a successful flash. So, I would try and flash it again.

Was motor running when you originally flashed it?

No, charger was connected to the batery.
Can you read something from log window??
tried flash again with same result

[TonyX3driver]

Originally Posted by TonyX3driver

No, charger was connected to the batery.
Can you read something from log window??
tried flash again with same result

always error message....

[TonyX3driver]

Originally Posted by TonyX3driver

always error message....

do you know meaning of this flashing left indicator?

[shawnsheridan]

Originally Posted by TonyX3driver

do you know meaning of this flashing left indicator?

No. I have seen it before on an F10 Kombi, and it was recoverable once flash took.

I do not know what is wrong with your flash though. I have read of others with this issue using a DHCP sever and getting it to work.

Send me TeamViewer Login, and I can look at it.

[TonyX3driver]

Originally Posted by shawnsheridan

No. I have seen it before on an F10 Kombi, and it was recoverable once flash took.

I do not know what is wrong with your flash though. I have read of others with this issue using a DHCP sever and getting it to work.

Send me TeamViewer Login, and I can look at it.

Wow! Update. Just now Kombi waked up after several flash repeating
Log say "finished with warnings.

How to find out if is flashed or original FW there??

[shawnsheridan]

Originally Posted by TonyX3driver

Wow! Update. Just now Kombi waked up after several flash repeating
Log say "finished with warnings.

How to find out if is flashed or original FW there??

Create new flash TAL (don't have to run it, just create it) and see if Kombi is targeted for new SWFL or not. If not, it has latest firmware from your PSdZData.

[TonyX3driver]

Originally Posted by shawnsheridan

Create new flash TAL (don't have to run it, just create it) and see if Kombi is targeted for new SWFL or not. If not, it has latest firmware from your PSdZData.

Just now quickly looked for HUD_ENTERTAINMENT_ENABLE and found it, modified and finally have music track on HUD!!!!

This was all this fight about.
Should I care for Log warning "finished with warnings"or not??
Made short tesr ride and scroll all the menu and seems to be all as before ok.

[shawnsheridan]

Originally Posted by TonyX3driver

Just now quickly looked for HUD_ENTERTAINMENT_ENABLE and found it, modified and finally have music track on HUD!!!!

This was all this fight about.
Should I care for Log warning "finished with warnings"or not??
Made short tesr ride and scroll all the menu and seems to be all as before ok.

I would not worry about Flash Log Errors. If you had E-Sys Option to Update MSM, it will give an error. All that matters is that car has no error codes.

[TonyX3driver]

Originally Posted by shawnsheridan

I would not worry about Flash Log Errors. If you had E-Sys Option to Update MSM, it will give an error. All that matters is that car has no error codes.

Good. Now, time to close garage and go for some good wine
It was very exciting time with clocks off.
Thank you once again for your support, very appreciate this. Wish to have some drink together, I'm due to you!
Best regards, Tony

[shawnsheridan]

Originally Posted by TonyX3driver

Good. Now, time to close garage and go for some good wine
It was very exciting time with clocks off.
Thank you once again for your support, very appreciate this. Wish to have some drink together, I'm due to you!
Best regards, Tony

[RolaNoCalhau]

Originally Posted by shawnsheridan

You can try, but for any ECU that has Trimmed CAFD you will not be able to find any FDL Codes.

No new E-Sys will solve this. The issue is all descriptive text has been removed from most of the PSdZData files.

Hi Shawn,

Initiated this today and so far just made FA and CAFD backup of original configuration files as per April1's tutorial.

However, when reading CAFD files, after "read coding data" in "coding" box, the error report reports 7 errors - please see attached report.
Is this a problem? Tried 3 or 4 times with same result.

Before continuing the process, 2 questions:

- did I do correctly disconnecting E-Sys after reading coding data? Should have done anything else before disconnect? Or is it safe to disconnect anytime anywhere?

- during the process I'm always afraid the car goes off, because I noticed already that after a while it goes off when listening to the radio. If it happens during E-Sys connection, independently of what I could be doing, can it damage or brick something?

Being too cautious because don't want to brick anything.

Tks in advance for your continued support.

[shawnsheridan]

Originally Posted by RolaNoCalhau

Hi Shawn,

Initiated this today and so far just made FA and CAFD backup of original configuration files as per April1's tutorial.

However, when reading CAFD files, after "read coding data" in "coding" box, the error report reports 7 errors - please see attached report.
Is this a problem? Tried 3 or 4 times with same result.

Before continuing the process, 2 questions:

- did I do correctly disconnecting E-Sys after reading coding data? Should have done anything else before disconnect? Or is it safe to disconnect anytime anywhere?

- during the process I'm always afraid the car goes off, because I noticed already that after a while it goes off when listening to the radio. If it happens during E-Sys connection, independently of what I could be doing, can it damage or brick something?

Being too cautious because don't want to brick anything.

Tks in advance for your continued support.

You can disconnect E-Sys anytime so long as you are not in the middle of writing data to ECU.

You should not be worrying about the car going off as the motor should be running during coding.

What PSdZData version are you using?

[RolaNoCalhau]

Originally Posted by shawnsheridan

You can disconnect E-Sys anytime so long as you are not in the middle of writing data to ECU.

You should not be worrying about the car going off as the motor should be running during coding.

What PSdZData version are you using?

PSdZData version 54.1

[shawnsheridan]

Originally Posted by RolaNoCalhau

PSdZData version 54.1

What is the Connection Target Name? It contains the I-Step (PSdZData) version.

[RolaNoCalhau]

Originally Posted by shawnsheridan

What is the Connection Target Name? It contains the I-Step (PSdZData) version.

How and where do I reach that?

Well, I have made some progress however.

In spite having the software version F010-15-03-501 = ISTA/P 2.55.0., it seems I was able find the FDL codes after all. Hope this be good news.

I was able to code already button on key fob to close trunk, and tried few others with no success. But I could find them.

Tried to remove the seatbelt warning but didn't find the 3001 section in ACSM module... how is it possible?

Another one I could use your help is to disable DVD speedlock. Please take a look at the attached print screen: as you can see I have no option to put value = FF as stated in the cheat chart. Can you help on this one?

Tried also the digital speed in BC (don't know what this means) and when finished coding an analogue speedometer showed up in the display below speed instrument but after 50 or 60 seconds disappeared. It reset the clock and nothing else. Do you have any suggestion?

[shawnsheridan]

Originally Posted by RolaNoCalhau

How and where do I reach that?

Well, I have made some progress however.

In spite having the software version F010-15-03-501 = ISTA/P 2.55.0., it seems I was able find the FDL codes after all. Hope this be good news.

I was able to code already button on key fob to close trunk, and tried few others with no success. But I could find them.

Tried to remove the seatbelt warning but didn't find the 3001 section in ACSM module... how is it possible?

Another one I could use your help is to disable DVD speedlock. Please take a look at the attached print screen: as you can see I have no option to put value = FF as stated in the cheat chart. Can you help on this one?

Tried also the digital speed in BC (don't know what this means) and when finished coding an analogue speedometer showed up in the display below speed instrument but after 50 or 60 seconds disappeared. It reset the clock and nothing else. Do you have any suggestion?

When you hit the Connect Button, you were presented a window with a list of Targets, and you selected one. This target had a name, something like F025-14-11-502.

FF is not available from the Dropdown list of predefined settings. You need to change the Werte Value directly:

E-Sys - How to Change Werte Values.pdf:

http://f30.bimmerpost.com/forums/att...3&d=1338274757

Digital speed appears in the BC Cluster, and you must cycle through the settings with the BC Stalk to display it.

[RolaNoCalhau]

Originally Posted by shawnsheridan

You can disconnect E-Sys anytime so long as you are not in the middle of writing data to ECU.

You should not be worrying about the car going off as the motor should be running during coding.

What PSdZData version are you using?

All the few coding I did was with the engine not running. Is it mandatory?

[shawnsheridan]

Originally Posted by RolaNoCalhau

All the few coding I did was with the engine not running. Is it mandatory?

No, not mandatory, but when the voltage drops too low, and you corrupt ECU CAFD file, you will just wish then you ran the motor per the instructions.