Coding made Easy: A step by step procedure - Page 12 - XBimmers

chx437 · 10-22-2012, 01:28 PM

A question for the coding experts here if you have you found any hints to:
- enable (or to disable) the rear lights when the main light switch is on "AUTOMATIC" and the DRLs are on ...in the first X3(F25) models upto 2012 the rear lights were on when DRLs were on but later after some SW update the rear lights were not any more on automatically
- disable (or to enable) the bulb monitoring for the flasher bulbs ...to prepare the change for flasher LED bulbs without additional parallel resistors

saggo · 10-23-2012, 03:10 AM

Quote:

Originally Posted by Colflqgg

What codes did you change to make the headlights fade on and to change the delay on the wiper spray?

Thanks!

Regarding the welcome light function, you can choose which group of lights on your vehicle are utilised for this function and how the ECU turns them on / off. Choosing the exponential function rather than the logarithmic type will result in a more 'even' rate of increase / decrease in brightness over time.

FRM 3050 WL_FUNKTION_AL
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: nicht_aktiv / Werte=00
Welcome Lights - Low Beam Lights - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

FRM 3050 WL_FUNKTION_FL
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: nicht_aktiv / Werte=00
Welcome Lights - High Beam - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

FRM 3050 WL_FUNKTION_KZL
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: hard_on / Werte=02
Welcome Lights - License Plate Lights - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

FRM 3050 WL_FUNKTION_NSW
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: nicht_aktiv / Werte=00
Welcome Lights - Fog Lights - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

FRM 3050 WL_FUNKTION_POL
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: hard_on / Werte=02
Welcome Lights - Position Lights (Angel Eyes and Front Side LED's) - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

FRM 3050 WL_FUNKTION_SSL
Options are: nicht_aktiv / soft_on / hard_on / soft_on_LED
Default setting: hard_on / Werte=02
Welcome Lights - Tail Lights - 0 = Off; 1 = Soft (log); 2 = Hard (instant on); 3 = Soft (exp)

Wash before Wipe delay:

JBBFE, 3000 Wipe_Wash, WASHWITHOUTWIPE_TIME

Default value on my X3 is 200mSec

For info, the first graph below shows the exponential function and the second logarithmic, you can see that the exponential is more 'linear'...

mge.92 · 10-23-2012, 04:13 PM

How do I code a BMW exx when I have the latest software and it will only allow me to code fxx vehicles?

shawnsheridan · 10-23-2012, 04:42 PM

Quote:

Originally Posted by mge.92

How do I code a BMW exx when I have the latest software and it will only allow me to code fxx vehicles?

You need NCS Expert and SP-Daten to code Exx Chassis.

lbjgh · 10-23-2012, 04:52 PM

Anyone know if the voltage can be displayed in the BC?

shawnsheridan · 10-23-2012, 04:53 PM

Quote:

Originally Posted by lbjgh

Anyone know if the voltage can be displayed in the BC?

Only through CIC Hidden Menu.

02420X3 · 10-23-2012, 05:33 PM

When I want to monitor voltage I use a plug-in Equus gauge in the cigarette lighter socket between the cupholders. $15 from Amazon US,

lbjgh · 10-25-2012, 03:53 PM

Something I found interesting tonight... I can view the owners manual while the car is in motion now.

I think it must be tied to dvd playback in motion.

It sure beats having to pull over and stop to check a feature especially if the passenger is doing the reading.

lbjgh · 10-25-2012, 03:54 PM

Something I found interesting tonight... I can view the owners manual while the car is in motion.

I think it must be tied to dvd playback in motion.

It sure beats having to pull over and stop to check a feature especially if the passenger is doing the reading.

April1 · 10-25-2012, 11:05 PM

Yes you are right. I had noticed it too.

gareth12468 · 10-26-2012, 08:47 AM

I need to get the cable now.....

tobert · 10-28-2012, 05:07 PM

Does anyone know how to code so the front orange turn signal lights do not come on when the parking lights are on (just the halo would illuminate)?

Also, does anyone know how when the headlights are set to auto, to make the fog light not illuminate when the turn signal is engaged?

shawnsheridan · 10-28-2012, 05:15 PM

Quote:

Originally Posted by tobert

Does anyone know how to code so the front orange turn signal lights do not come on when the parking lights are on (just the halo would illuminate)?

Also, does anyone know how when the headlights are set to auto, to make the fog light not illuminate when the turn signal is engaged?

I'm not sure if anyone ever confirmed it, but for the Side Markers, look for this or something similar:

FEM_BODY / 3063 LceLampMapping2 / MAPPING_SIDEMARKER_L_OUTPUT = off
FEM_BODY / 3063 LceLampMapping2 / MAPPING_SIDEMARKER_R_OUTPUT = off

Not sure about the Fog Lights.

chx437 · 11-05-2012, 04:59 PM

Once again here's one needing info where to download psdzdata 47.4
...shawnheridian, april1 please

saggo · 11-05-2012, 05:18 PM

Quote:

Originally Posted by shawnsheridan

Only through CIC Hidden Menu.

Forgive my ignorance, how do you access this hidden menu?

lbjgh · 11-05-2012, 06:16 PM

I haven't tried this on my car but it may be worth a try:

Quote:

Originally Posted by saggo

Forgive my ignorance, how do you access this hidden menu?

shawnsheridan · 11-06-2012, 12:50 AM

Quote:

Originally Posted by chx437

Once again here's one needing info where to download psdzdata 47.4
...shawnheridian, april1 please

PM Sent.

shawnsheridan · 11-06-2012, 12:54 AM

Quote:

Originally Posted by saggo

Forgive my ignorance, how do you access this hidden menu?

Hold down the odometer reset button and turn the ignition on by pushing start/stop button.
Release the odometer reset button, and you should see a menu of 4 items on the dashboard. From here on, use the odo-reset button to advance to the next entry through a short press, and to select through a long press.
Choose the one that says Unlock through the above, which will take you to a passkey screen. Your passkey is the sum of the last 5 digits of your VIN. Increment the two-digit number until you get to it, and with the long press of the odo button, select it.

chx437 · 11-06-2012, 01:04 AM

Quote:

Originally Posted by shawnsheridan

PM Sent.

Thanks

!!!

saggo · 11-06-2012, 07:09 AM

Quote:

Originally Posted by shawnsheridan

Hold down the odometer reset button and turn the ignition on by pushing start/stop button.
Release the odometer reset button, and you should see a menu of 4 items on the dashboard. From here on, use the odo-reset button to advance to the next entry through a short press, and to select through a long press.
Choose the one that says Unlock through the above, which will take you to a passkey screen. Your passkey is the sum of the last 5 digits of your VIN. Increment the two-digit number until you get to it, and with the long press of the odo button, select it.

Many Thanks - I'll play later!

pacecapt · 11-06-2012, 12:55 PM

How do I load my vehicle coding (CAF/.ncd) files into E-Sys in order to edit or view them when not connected to my vehicle? I have gone through the E-Sys "Editors and Viewers" Tab documentation but it seems to have missed a step. I am able to copy and move the .ncd files but I can't seem to load them as it keeps asking me for an FA and that folder is empty. I have not been able to connect the dots between page 2 and 3 of that Tab.

chx437 · 11-07-2012, 06:59 AM

New with E-Sys and some beginners problems:
- when installed the software all went Ok
- ZGW_Search detects the ENET cable Ok and gets e.g. the VIN

But when starting the E-Sys it cannot connetc to the car:

"Detection of programming target failed. [C032]

MCDError Severity: 2051, Error Code: 53315, Description:
internal error, Vendor Code: 28, Vendor Description:
could not parse Db project [2130759747] - SYSTEM_ERROR"

I tried two laptops (both running Win7 x64) but the same error from both.
One additional detail: E-Sys never asked any PIN ...is this normal?

Anyone had similar experience ...any hint how to get forward?

Here's the error msg with all the detailed text:

10-23-2012, 04:52 PM	#247
lbjgh Major Drives: 2013 AW X3 M-Sport Join Date: Dec 2011 Location: North of Toronto Posts: 1,232 iTrader: (0)	Anyone know if the voltage can be displayed in the BC? __________________ 2013, AW, xDrive35i, M Sport Package, Technology Package, Dynamic Comfort Package, Premium Package, 3M Clear Bra, Euro foglight switch, a few coded fixes

10-25-2012, 03:53 PM	#250
lbjgh Major Drives: 2013 AW X3 M-Sport Join Date: Dec 2011 Location: North of Toronto Posts: 1,232 iTrader: (0)	Something I found interesting tonight... I can view the owners manual while the car is in motion now. I think it must be tied to dvd playback in motion. It sure beats having to pull over and stop to check a feature especially if the passenger is doing the reading. __________________ 2013, AW, xDrive35i, M Sport Package, Technology Package, Dynamic Comfort Package, Premium Package, 3M Clear Bra, Euro foglight switch, a few coded fixes

10-25-2012, 03:54 PM	#251
lbjgh Major Drives: 2013 AW X3 M-Sport Join Date: Dec 2011 Location: North of Toronto Posts: 1,232 iTrader: (0)	Something I found interesting tonight... I can view the owners manual while the car is in motion. I think it must be tied to dvd playback in motion. It sure beats having to pull over and stop to check a feature especially if the passenger is doing the reading. __________________ 2013, AW, xDrive35i, M Sport Package, Technology Package, Dynamic Comfort Package, Premium Package, 3M Clear Bra, Euro foglight switch, a few coded fixes

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

10-22-2012, 01:28 PM	#243
chx437 New Member Drives: BMW X3(F25) Join Date: Jun 2011 Location: Finland Posts: 17 iTrader: (0)	A question for the coding experts here if you have you found any hints to: - enable (or to disable) the rear lights when the main light switch is on "AUTOMATIC" and the DRLs are on ...in the first X3(F25) models upto 2012 the rear lights were on when DRLs were on but later after some SW update the rear lights were not any more on automatically - disable (or to enable) the bulb monitoring for the flasher bulbs ...to prepare the change for flasher LED bulbs without additional parallel resistors

10-23-2012, 04:13 PM	#245
mge.92 SPEED RACER Drives: X3 28I M SPORT Join Date: Jul 2012 Location: Washington DC Posts: 71 iTrader: (0)	How do I code a BMW exx when I have the latest software and it will only allow me to code fxx vehicles?

10-23-2012, 05:33 PM	#249
02420X3 Lieutenant Drives: 2011 X3 35i Join Date: Jun 2011 Location: Boston Posts: 546 iTrader: (0)	When I want to monitor voltage I use a plug-in Equus gauge in the cigarette lighter socket between the cupholders. $15 from Amazon US,

10-25-2012, 11:05 PM	#252
April1 Love All Drives: X3 28i 2011 Join Date: Nov 2011 Location: San Francisco Posts: 735 iTrader: (1)	Yes you are right. I had noticed it too.

10-26-2012, 08:47 AM	#253
gareth12468 First Lieutenant Drives: 2011 X3 xDrive 28i Join Date: Mar 2011 Location: Toronto Posts: 307 iTrader: (0) Garage List 2011 BMW X3 [0.00]	I need to get the cable now.....

10-28-2012, 05:07 PM	#254
tobert New Member Drives: 2013 X3 28i Join Date: Sep 2012 Location: Boston, MA Posts: 9 iTrader: (0)	Does anyone know how to code so the front orange turn signal lights do not come on when the parking lights are on (just the halo would illuminate)? Also, does anyone know how when the headlights are set to auto, to make the fog light not illuminate when the turn signal is engaged?

11-05-2012, 04:59 PM	#256
chx437 New Member Drives: BMW X3(F25) Join Date: Jun 2011 Location: Finland Posts: 17 iTrader: (0)	Once again here's one needing info where to download psdzdata 47.4 ...shawnheridian, april1 please

11-06-2012, 12:55 PM	#263
pacecapt Enlisted Member Drives: 2011 528i & 2013 X3 28i Join Date: Sep 2011 Location: Florida Posts: 38 iTrader: (0) Garage List 2011 BMW 528i [0.00] 2013 BMW X3 28i [0.00]	How do I load my vehicle coding (CAF/.ncd) files into E-Sys in order to edit or view them when not connected to my vehicle? I have gone through the E-Sys "Editors and Viewers" Tab documentation but it seems to have missed a step. I am able to copy and move the .ncd files but I can't seem to load them as it keeps asking me for an FA and that folder is empty. I have not been able to connect the dots between page 2 and 3 of that Tab.